(2)
Remove the filter bowl (3) together with the filter element (2). NOTE : You may have to pull the filter element (2) to release it from
____
the filter head (1).
(3)
Discard the filter element (2).
(4)
Clean the filter bowl (3) and apply HYDRAULIC FLUIDS (Material No. 02-003) to its threads.
(5)
Install the filter bowl (3) in the filter head (1) and tighten it with your hands.
(6)
Safety the filter bowl (3) to the filter head (1) with lockwire, corrosion-resistant steel, dia. 0.8 mm (0.032 in.).
(7)
If the red clogging indicator is out, push it in to set it again. Subtask 29-10-00-860-088
B.
Preparation for the Test
(1)
Make sure that the content of the reservoir of the Yellow hydraulic system is correct. Add fluid as necessary (Ref. TASK 12-12-29-611-001) or (Ref. TASK 12-12-29-611-002).
(2)
Pressurize the reservoir of the Yellow hydraulic system (Ref. TASK 29-14-00-614-002).
(3)
Remove the warning notice(s).
(4)
Remove the container. Subtask 29-10-00-710-053
C.
Test
(1)
Dry-motor the right (No. 2) engine (Ref. TASK 71-00-00-710-001).
(2)
Make sure that there are no hydraulic leaks from the filter assembly, and that the clogging indicator stays in.
(3)
If the clogging indicator comes out, push it in to set it again. If it will not stay in, do the trouble-shooting of the filter assembly to find the cause.
(4)
Stop the operation of the right (No. 2) engine (Ref. TASK 71-00-00-710-001).
5. Close-up
________ Subtask 29-10-00-410-059
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the left fan cowl door of the right (No. 2) engine (Ref. TASK 71-13-00-410-040).
TASK 29-10-00-440-002
Reactivation of the Case Drain Filter (3084GM) of the Engine Driven Pump of the Yellow Hydraulic System
1. Reason for the Job
__________________
Refer to the MMEL TASK: 29-10-07
Main Hydraulic Power - Filters
Case Drain Filters
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific warning notices
No specific container 2.0 l (0.5283 USgal)
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
No specific lockwire, corrosion-resistant steel, dia. 0.8 mm
(0.032 in.)
R Material No. 02-003 F NSA 307110 TYPE 4 HYDRAULIC FLUID (PHOSPHATE ESTER BASE) (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
12-12-29-611-001 Fill the Hydraulic Fluid Reservoir with a Hand Pump 12-12-29-611-002 Fill the Hydraulic Fluid Reservoir with a Hydraulic Service Cart 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
Configuration before Maintenance Action 29-00-00-910-002 Safety Procedures of the Hydraulic System 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 29-14-00-614-002 Pressurization of the Hydraulic Reservoirs through
the Ground Connector
71-00-00-710-001 Dry Motoring Check
71-13-00-010-040 Opening of the Fan Cowl Doors
71-13-00-410-040 Closing of the Fan Cowl Doors
R 29-10-00-991-002 Fig. 401
3. Job Set-up
__________
Subtask 29-10-00-860-089
A. Aircraft Maintenance Configuration
WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.
_______
(1)
Obey the hydraulic safety procedures (Ref. TASK 29-00-00-910-002).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓1(106)
