RUD TRIM/RESET Pushbutton Switch
Figure 401/TASK 22-62-12-991-001
1EFF : ALL 1 22-62-12 Page 403
1 1 Feb 01/98
1 1
1CES 1
(4)
Loosen the four screws (4) that attach the plate (10) to the structure of the panel 110VU (16).
(5)
Remove the plate (10).
(6)
Remove the nut (3), the lockwasher (2) and the washer (1) from the RUD TRIM/ RESET pushbutton switch (14).
(7)
Remove the RUD TRIM/RESET pushbutton switch (14) from the structure of the panel 110VU (16).
(8)
Loosen the screws of the terminals at the rear of the RUD TRIM/RESET pushbutton switch (14) to disconnect the electrical wires and make a mark on each wire.
(9)
Remove the RUD TRIM/RESET pushbutton switch (14).
1EFF : ALL 1 22-62-12Page 404 1 1 Feb 01/98 1 1 1CES 1
TASK 22-62-12-400-001
Installation of the RUD TRIM/RESET Pushbutton Switch (8CC)
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE WHEEL CHOCKS ARE IN POSITION.
_______
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
22-62-00-710-001 Operational Test of the Rudder Trim Function 22-96-00-710-001 Operational Test of the AFS 22-97-00-710-001 Operational Test of the LAND CAT III Capability 32-45-00-710-001 Operational Test of the Parking Brake System 22-62-12-991-001 Fig. 401
1EFF : ALL 1 22-62-12Page 405 1 1 Feb 01/98 1 1 1CES 1
3. Job Set-up
__________
Subtask 22-62-12-865-052
A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AUTO FLT/FAC1/28VDC 5CC1 B04 121VU AUTO FLT/RUDDER/TRIM/IND 15CC M20 121VU AUTO FLT/FAC2/28VDC 5CC2 M19 121VU HYDRAULIC/PARK BRK/CTL/STBY 71GG N37 121VU HYDRAULIC/PARK BRK/CTL/NORM 70GG N36
R 122VU LIGHTING/INSTL LT/MAIN INST/PNL AND/PED 4LF Y04
4. Procedure
_________
Subtask 22-62-12-420-052
A. Installation of the RUD TRIM/RESET Pushbutton Switch (8CC)
(Ref. Fig. 401/TASK 22-62-12-991-001)
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
On the rear of the RUD TRIM/RESET pushbutton switch (14) install each electrical wire in its initial position (refer to the marks) and tighten the screws.
(4)
Install the RUD TRIM/RESET pushbutton switch (14) on the structure of the panel 110VU (16).
(5)
Install the washer (1), the lockwasher (2) and the nut (3).
(6)
Put the plate (10) in the correct position on the structure of the panel 110VU (16).
(7)
Install the four screws (4).
(8)
Install the knob (5) on the shaft of the control switch (15).
(9)
Lock the knob (5) with the two screws (6).
1EFF : ALL 1 22-62-12Page 406 1 1 Feb 01/99 1 1 1CES 1
(10) Install the knob (7) (in the OFF position), the pin (9) and the screw
(8). Subtask 22-62-12-420-053
B. Installation of the Panel 110VU
(Ref. Fig. 401/TASK 22-62-12-991-001)
(1)
Remove the blanking caps from the electrical connectors.
(2)
Make sure that the electrical connectors are clean and in the correct condition.
(3)
Connect the four electrical connectors (13).
(4)
Install the panel 110VU (16) on the support bracket (12).
(5)
Lock the panel 110VU (16) with the four quarter-turn fasteners (11). Subtask 22-62-12-865-053
C.
Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 4LF, 5CC1, 5CC2, 15CC, 70GG, 71GG
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM AUTO FLIGHT 自動飛行2(23)
