(1)
Remove the blanking caps from the electrical connectors.
(2)
Make sure that the electrical connectors are clean and in the correct condition.
(3)
Connect the four electrical connectors (10).
(4)
Install the panel 110VU (11) on the support bracket (9).
(5)
Lock the panel 110VU (11) with the four quarter-turn fasteners (8). Subtask 22-62-11-865-052
C.
Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 4LF, 5CC1, 5CC2, 15CC, 70GG, 71GG
Subtask 22-62-11-710-050
D. Operational Tests
(1) Do the operational test of the AFS to check the rudder trim function (Ref. TASK 22-96-00-710-001).
NOTE : If the aircraft is operated in CAT 3 conditions, you must also
____ do the test below: Land CAT 3 Capability Test (Ref. TASK 22-97-00-710-001).
NOTE : As an alternative procedure, you can do this operational test
____ without the CFDS (Ref. TASK 22-62-00-710-001).
(2) Do the operational test of the parking brake system (Ref. TASK 32-45-00-710-001).
1EFF : ALL 1 22-62-11Page 407 1 1 Feb 01/98 1 1 1CES 1
5. Close-up
________ Subtask 22-62-11-860-050
A. Put the aircraft back to its initial configuration.
(1)
Remove the warning notice(s).
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 22-62-11Page 408 1 1 Feb 01/98 1 1 1CES 1
PUSHBUTTON SWITCH - RUDDER TRIM/ RESET (8CC) - REMOVAL/INSTALLATION
___________________________________________________________________ TASK 22-62-12-000-001 Removal of the RUD TRIM/RESET Pushbutton Switch (8CC) WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE WHEEL CHOCKS ARE IN POSITION.
_______
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
22-62-12-991-001 Fig. 401
1EFF : ALL 1 22-62-12Page 401 1 1 Feb 01/98 1 1 1CES 1
3. Job Set-up
__________
Subtask 22-62-12-865-050
A. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AUTO FLT/FAC1/28VDC 5CC1 B04 121VU AUTO FLT/RUDDER/TRIM/IND 15CC M20 121VU AUTO FLT/FAC2/28VDC 5CC2 M19 121VU HYDRAULIC/PARK BRK/CTL/STBY 71GG N37 121VU HYDRAULIC/PARK BRK/CTL/NORM 70GG N36
R 122VU LIGHTING/INSTL LT/MAIN INST/PNL AND/PED 4LF Y04
4. Procedure
_________
Subtask 22-62-12-020-050
A. Removal of the Panel 110VU
(Ref. Fig. 401/TASK 22-62-12-991-001)
(1)
Loosen the four quarter-turn fasteners (11) to release the panel 110VU (16).
(2)
Carefully lift the panel 110VU (16) to get access to the electrical connectors (13).
(3)
Disconnect the four electrical connectors (13).
(4)
Put blanking caps on the disconnected electrical connectors.
(5)
Remove the panel 110VU (16).
Subtask 22-62-12-020-051
B.
Removal of the RUD TRIM/RESET Pushbutton Switch (8CC)
(Ref. Fig. 401/TASK 22-62-12-991-001)
(1)
Loosen the two screws (6) of the knob (5).
(2)
Remove the knob (5) from the shaft of the control switch (15).
(3)
Remove the screw (8), the pin (9) and the knob (7).
1EFF : ALL 1 22-62-12Page 402 1 1 Feb 01/99 1 1 1CES 1
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM AUTO FLIGHT 自動飛行2(22)
