(d)
 Put the sleeve (59) in position on the flange (10).

 (e)
 Put the retaining cables (60) in position in the flange (10) and install the new washers (64) and the new nuts (66).

 (f)
 Put the retaining cables (96) in position on the flange (4) and install the new washers (64) and the new nuts (66).

 (g)
 Put the sleeve (88) in position on the flange (4).

 (h)
 Torque the nuts (65) and (66) to between 0.8 and 1.0 m.daN (70.79 and 88.49 lbf.in).

 (i)
 Wipe clean the excess COMMON GREASE (Material No. 04-012) from the retaining cables (96).

 (3) Install the pipe assembly 11HM10 (11HM11) (Ref. TASK 21-52-23-400-001).
 NOTE : Do not install the access panel/s at this time.
____
 1EFF : ALL 1 21-52-24Page 454 1 1 Aug 01/05R 1 1 1CES 1

 (4)
 Put the clamp (12) and the sleeve (13) in position on the heat
 exchanger unit (7).

 (5)
 Torque the clamp (12) to between 0.08 and 0.12 m.daN (7.07 and 10.61 lbf.in).

 (6)
 Put the sleeve (16) and the duct (15) in position on the heat
 exchanger unit (7).

 (7)
 Remove the protective cover from the cooling elements of the heat
 exchanger unit (7).

 (8)
 Install the inlet plenum (46):

 (a)
 For the left heat exchanger unit (10HM4), 1 Put the seals (43) and (47), and the inlet plenum (46) in

_
 position on the heat exchanger unit (7).

 (b)
 For the right heat exchanger unit (11HM4), 1 Put the seals (143) and (147), and the inlet plenum (46) in

_
 position on the heat exchanger unit (7).

 (9) Install the screws (48), the washers (49) and the nuts (50).
 (10)
 Put the bonding strap (41) in position and install the screw (42), the washer (44) and the nut (45) (Ref. TASK 20-28-00-912-004).

 (11)
 Put the clamp (9) and the sleeve (8) in position on the heat exchanger unit (7).

 (12)
 Tighten the clamp (9).

 (13)
 Install the air conditioning pack 10HM (11HM) (Ref. TASK 21-52-41-400-001).

 1EFF : ALL 1 21-52-24Page 455 1 1 Aug 01/05R 1 1 1CES 1

 Subtask 21-52-24-710-051
 C. Test
 (1)
 Do the pre-conditioning through the HP ground connector (Ref. TASK 12-33-21-618-001) or with the APU (Ref. TASK 12-33-21-618-001).

 (2)
 Do a leak check of the heat exchanger unit connections. NOTE : Minimum leakage is permitted. After the pack operates some

____ minutes, the leakage of air will reduce because the seals have their correct operating temperature.

 (3)
 After approx. 15 minutes stop the pre-conditioning (Ref. TASK 12-33-21-618-001) (Ref. TASK 12-33-21-618-001).

 (4)
 Do the operational test of the cockpit and cabin temperature control (Ref. TASK 21-63-00-710-004).

 5. Close-up
________ Subtask 21-52-24-410-052
 A. Close Access
 (1) Install the access panel/s (Ref. TASK 53-35-13-400-002).
 (a)
 FOR 10HM4

 -191KB
 -191BB,

 (b)
 FOR 11HM4

 -192KB
 -192FB.
 1EFF : ALL 1 21-52-24Page 456 1 1 Aug 01/05R 1 1 1CES 1

 HEAT EXCHANGER UNIT (10HM4,11HM4) - INSPECTION/CHECK
____________________________________________________
 TASK 21-52-24-200-001
 Attachment Components (In-Service Wear Limits) - Heat Exchanger 10HM4 (11HM4)
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
21-52-00-300-001 Attachment Components - Repair/Replacement

R CMM 215211
R CMM 215212
 21-52-24-991-004 Fig. 601
 3. Job Set-up
__________
 Subtask 21-52-24-860-054

 A. Aircraft Maintenance Configuration
 (1) Make sure that the applicable components are disassembled to do the inspection procedure.

 4. Procedure_________
 (Ref. Fig. 601/TASK 21-52-24-991-004)
 Subtask 21-52-24-210-053
 A. Visual Inspection of the Spherical Bearings in the Support Rods and Bracket
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM AIR CONDITIONING 空調 4(78)