(e)
 Apply a small quantity of COMMON GREASE (Material No. 04-012) to the contact faces of the retaining cables (11).

 (3)
 Put the packings (16) in position on the condensor (22) and on the air cycle machine (17).

 (4)
 Put the sleeve (14) in position on the air cycle machine (17).

 (5)
 Put the sleeve (10) in position on the coupling (12).

 (6)
 Put the packing (21) in position on the condensor (22).

R 1EFF : 106-149, 229-299, 303-399, 1 21-52-32Page 424 1 1 Aug 01/05 1 1 1CES 1

 (7)
 Put the condensor (22) in position and install the support rods (72B) and (73).

 (8)
 Install the bushings (31), (where fitted the washers (30)), the bolts (29), the washers (33) and the nuts (34).

 (9)
 Install the clamp (20).

 (10)
 Make sure that the clamp (20) is in the correct position.

 (11)
 TORQUE the clamp (20) to between 0.51 and 0.56 m.daN (45.13 and 49.55 lbf.in).

 (12)
 Move the sleeve (14) in position over the packings (16) and install the half clamps (13) and the clamp (15).

 (13)
 TORQUE the clamp (15) to between 0.28 and 0.38 m.daN (24.77 and 33.62 lbf.in) and safety with annealed stainless-steel lockwire, diameter

 0.5 mm (0.0196 in.) MISCELLANEOUS (Material No. 19-009).

 (14)
 Move the sleeve (10) in position on the condensor (22).

 (15)
 Put the retaining cables (11) in position and install the new washers

 (7) and the new nuts (6).
 NOTE : Hold the hexagon part of the retaining cables (11) to prevent

____ twisting of the cables when you install the nuts (6).
 (16) TORQUE the nuts (6) to between 0.85 and 1.0 m.daN (75.22 and 88.49 lbf.in) and wipe clean the excess COMMON GREASE (Material No. 04-012) from the retaining cables (11).
 NOTE : Hold the hexagon part of the retaining cables (11) to prevent
____ twisting of the cables when you torque the nuts (6). Make sure that there is no tension in the cables (11). This will give a safe and flexible connection.
 (17)
 Put the sleeve (23) in position on the condensor (22) and install the clamp (24).

 (18)
 Make sure that the clamp (24) is in the correct position.

 (19)
 TORQUE the clamp (24) to 0.28 m.daN (24.77 lbf.in).

 (20)
 Connect the sense lines (3), (8), and (18).

R 1EFF : 106-149, 229-299, 303-399, 1 21-52-32Page 425 1 1 Aug 01/05 1 1 1CES 1

 (21) TORQUE the sense lines (3), (8), and (18) to between 0.9 and 0.915
 m.daN (79.64 and 80.97 lbf.in).
 (22) Remove the blanking caps and connect the electrical connector (27).
 (23) Make sure that the work area is clean and clear of tool(s) and other
 items. 
R  **ON A/C 401-499, 
R  Subtask 21-52-32-420-052-B 
R  C. Installation of the Condensor 
R  NOTE : Turn the sleeves (8) and (12) when you move them or when you____ 
R  install them. This will help to prevent damage to the internal 
R  seals or packings. 
R  Do an inspection of the sleeve (20) for damage, wear, blisters in 
R  the material and seperation of the material from the wire 
R  reinforcement. 
R  If necessary replace the sleeve (Ref. TASK 21-52-43-000-001) and 
R  (Ref. TASK 21-52-43-400-001): 
R  for the condensor 10HM2, 
R  - sleeve (20). 
R  for the condensor 11HM2, 
R  - sleeve (20). 
R  (1) Prepare the attachment components for installation, 
R  (a) Clean the component interface and/or the adjacent area. 
R  (b) Apply a small quantity of: 
R  - COMMON GREASE (Material No. 04-007) 
R  or 
R  - LUBRICANTS (Material No. 06-007) 
R  to the new packing (14) and packing (18), and to the new seal
 (7) 
R  before you install them. 
R  NOTE : The material 04-007 is a molybdenum disulfide powder.____ 
R  Before you can apply it you must first make it into a 
R  paste. To do this you must mix the powder with pure water 
R  or white spirit. 
R  NOTE : The material 06-007 is applied dry.____ 

R 1EFF : 106-149, 229-299, 303-399, 401-499, 1 21-52-32Page 426 1 1 Aug 01/05 1 1 1CES 1

R  (c) Put the new seals (7) in position in the sleeve (8) (Ref. TASK 
R  20-26-00-910-002). 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM AIR CONDITIONING 空調 4(100)