(2)
Make sure that the work area is clean and clear of tool(s) and other items.
EFF : ALL
11-00-00Page 238
May 01/05
R
CES TASK 11-00-00-960-002
Replacement of the Engine Leasing Plate
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific warning notice
No specific access platform 1.50 m (4 ft. 11 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
No specific lockwire, corrosion resistant steel 0.5 mm (0.020
in.) Material No. 11-002 USA MIL-PRF-680
DRY CLEANING SOLVENT (VARSOL/WHITE SPIRIT)
(Ref. 20-31-00) Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 71-13-00-410-040 Closing of the Fan Cowl Doors
EFF : ALL
11-00-00Page 239
May 01/05
R
CES 3. Job Set-up
__________ Subtask 11-00-00-941-055
A. Safety Precautions
(1)
On the center pedestal, on the ENG panel 115VU:
(a) Put a warning notice in position to tell persons not to start the engine.
(2)
Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3)
On the ENG section of the maintenance panel 50VU:
(a)
Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b)
Put a warning notice in position to tell persons not to energize the FADEC 1(2).
Subtask 11-00-00-010-051
B. Get Access
(1)
Open the fan cowl doors (Ref. TASK 71-13-00-010-040):
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
(2)
Put an access platform in position at the engine.
4. Procedure
_________ Subtask 11-00-00-020-050
A. Removal of the Engine Leasing Plate
(1)
Cut, remove and discard the lockwire.
(2)
Remove the nuts, the screws and the washers that attach the leasing plate.
(3)
Remove the leasing plate.
EFF : ALL
11-00-00Page 240
May 01/05
CES
Subtask 11-00-00-110-067
B. Cleaning of the Contact Surface
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1) Clean and degrease the contact surface of the leasing plate with a lint-free cloth MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-002).
Subtask 11-00-00-960-050
C. Installation of the Engine Leasing Plate
(1)
Put the leasing plate in position on the support.
(2)
Install the washers, the screws and the nuts.
(3)
Safety the two screws together on every side of the plate with lockwire, corrosion resistant steel 0.5 mm (0.020 in.).
5. Close-up
________
Subtask 11-00-00-942-067
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the access platform(s).
(3)
Close the fan cowl doors (Ref. TASK 71-13-00-410-040):
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM PLACARDS AND MARKINGS(23)
