(2)
Remove the access platform(s).
ZONAL INSPECTION : WING AILERON - INSPECTION/CHECK
__________________________________________________ TASK 05-25-90-200-001 Zonal Inspection of the Wing Aileron
1. Reason for the Job
__________________
Refer to the MPD TASK: ZL-590-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 2 m (6 ft. 7 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
05-25-90-991-001 Fig. 601
3. Job Set-up
__________ Subtask 05-25-90-010-050
A. Get Access
(1)
Put an access platform in position.
(2)
Remove the access panels
590AB, 590BB.
690AB, 690BB.
(Ref. Fig. 601/TASK 05-25-90-991-001)
Access Panels of the Wing Aileron
Figure 601/TASK 05-25-90-991-001
1EFF : ALL 1 05-25-90 Page 602
1 1 Feb 01/98
1 1
1CES 1
4. Procedure
_________
Subtask 05-25-90-210-050
A. Inspection
(1)
Do a general visual inspection of the aileron.
(2)
Make sure that there are no signs of corrosion, cracks or damage.
(3)
Make sure that all the installations are attached correctly.
5. Close-up
________ Subtask 05-25-90-410-050
A. Close Access
(1)
Install the access panels
590AB, 590BB.
690AB, 690BB.
(2)
Remove the access platform(s).
ZONAL INSPECTION : LANDING GEAR AND LANDING GEAR DOORS - INSPECTION/CHECK
_________________________________________________________________________
TASK 05-27-00-200-001
Zonal Inspection as far as Visible from the Ground of the Landing Gear and the Landing Gear Doors
1. Reason for the Job
__________________
R R Self Explanatory
2.
Job Set-up Information
______________________
Not Applicable
3.
Job Set-up
__________
Subtask 05-27-00-869-050
A. Not applicable
4. Procedure
_________
Subtask 05-27-00-210-050
A. Inspection
(1)
Do a general visual inspection of the landing-gear and the landing-gear doors from the ground during the aircraft walkaround.
(2)
Make sure that there are no signs of corrosion, cracks or damage.
ZONAL INSPECTION : NOSE GEAR AND DOORS - INSPECTION/CHECK
_________________________________________________________
TASK 05-27-10-200-001
R R Zonal Inspection of Nose Gear and Nose Gear Doors
1. Reason for the Job__________________
R Refer to the MPD TASK: ZL-711-01
2. Job Set-up Information______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-22-00-010-001 32-22-00-410-001 Nose Gear Doors - Ground Doors OpeningNose Gear Doors - Ground Doors Closing
3. Job Set-up__________
Subtask 05-27-10-010-050
A. Get Access
(1) Open the nose gear doors 713 and 714. (Ref. TASK 32-22-00-010-001)
4. Procedure_________
Subtask 05-27-10-210-050
A. Inspection
R R R (1) Do a general visual inspection of the nose gear, the nose gear doors and the leg door attached to the nose gear. This inspection includes the zones 711, 712, 713, 714, 715 and 716.
(2) Make sure that there are no signs of corrosion, cracks or damage.
(3) Make sure that all the installations (wiring, ducting, piping) are attached correctly.
5. Close-up
________
Subtask 05-27-10-410-050
A. Close Access
(1) Close the nose gear doors 713 and 714. (Ref. TASK 32-22-00-410-001)
中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM 時間限制/維護檢查 1(87)
