3. Job Set-up
__________

 Subtask 05-23-20-010-052
 A. Get Access
 (1)
 Put an access platform in position at the zone 320.

 (2)
 Remove the access panels:
 321AL, (Ref. TASK 53-45-11-000-001)
 323AL, 323AR, (Ref. TASK 53-55-11-000-001)
 325AR, 325AL, (Ref. TASK 53-55-12-000-001)
 322BL. (Ref. TASK 55-32-11-000-001)

 (3)
 Remove and discard the aluminium tape from the lightening holes in the front spar.

 4. Procedure
_________ Subtask 05-23-20-210-052
 A. Inspection
 (1)
 Do a general visual inspection of the spar box of the vertical stabilizer.

 (2)
 Make sure that there are no signs of corrosion, cracks or damage.

 (3)
 Make sure that all the installations (wiring, ducting, piping) are attached correctly.

 5. Close-up
________ Subtask 05-23-20-410-052
 A. Close Access
 (1)
 Cut and install the BONDING AND ADHESIVE COMPOUNDS (Material No. 08-061) over the lightening holes on the front spar.

 (2)
 Install the access panels:
 322BL, (Ref. TASK 55-32-11-400-001)
 325AR, 325AL, (Ref. TASK 53-55-12-400-001)
 323AR, 323AL, (Ref. TASK 53-55-11-400-001)
 321AL
 (Ref. TASK 53-45-11-400-001)

 (3)
 Remove the access platform(s).

 TASK 05-23-20-200-004

R  Zonal Inspection of Vertical Stabilizer Tip
 1. Reason for the Job__________________
 Refer to the MPD TASK: ZL-324-01
 2. Job Set-up Information______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific  access platform 11 m (36 ft. 1 in.)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R  55-34-11-000-001 55-34-11-400-001  Removal of the Vertical Stabilizer Tip Installation of the Vertical Stabilizer Tip
 3. Job Set-up__________
 Subtask 05-23-20-010-053
 A. Get Access 
R R  (1) Put an access platform in position at the vertical stabilizer tip level.
 (2) Remove the vertical stabilizer tip 324AT. (Ref. TASK 55-34-11-000-001)
 4. Procedure_________
 Subtask 05-23-20-210-053
 A. Inspection
 (1) Do a general visual inspection of the vertical stabilizer tip.
 (2) Make sure that there are no signs of corrosion, cracks or damage.

 (3) Make sure that all the installations (wiring) are attached correctly.

 5. Close-up
________ Subtask 05-23-20-410-053
 A. Close Access
 (1)
 Install the vertical stabilizer tip 324AT. (Ref. TASK 55-34-11-400-001)

 (2)
 Remove the access platform(s).

 TASK 05-23-20-200-005

 Zonal Inspection of the Trailing Edge of the Vertical Stabilizer
 1. Reason for the Job
__________________
 Refer to the MPD TASK: ZL-325-01
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE  QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific  access platform 10 m (32 ft. 10 in.)
 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
55-33-13-010-001  Opening of the Trailing Edge Access-Panels 325EL, 325ER, 325DL, 325DR, 325CL, 325CR, 325BL and 325BR
 55-33-13-010-002  Opening/Removal of the Trailing Edge Access-Panels 325EL, 325ER, 325DL, 325DR, 325CL, 325CR, 325BL and 325BR
 55-33-13-410-001  Closing of the Trailing Edge Access-Panels 325EL, 325ER, 325DL, 325DR, 325CL, 325CR, 325BL and 325BR
 55-33-13-410-002  Closing/Installation of the Trailing Edge Access-Panels 325EL, 325ER, 325DL, 325DR, 325CL, 325CR, 325BL and 325BR
 3. Job Set-up
__________
 Subtask 05-23-20-010-054
 A. Get Access
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 時間限制/維護檢查 1(60)