**ON A/C ALL
 4. Procedure
_________
 Subtask 05-25-30-210-056

 A. Inspection
 (1)
 Do a general visual inspection of the flap track No. 4 and the related fairing.

 (2)
 Make sure that there are no signs of corrosion, cracks or damage.

 (3)
 Make sure that all the installations are attached correctly.

 5. Close-up
________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 Subtask 05-25-30-410-056
 A. Close Access
 (1)
 Install the flap track fairings:
 533AB, 533BB, 533CB,
 633AB, 633BB, 633CB
 (Ref. TASK 57-55-11-400-001).

 (2)
 Install the covers:
 533AL, 533AR, 533AT, 533DB,
 633AL, 633AR, 633AT, 633DB
 (Ref. TASK 57-55-11-400-001).

 (3)
 Remove the access platform(s).

 **ON A/C 301-399,

 Subtask 05-25-30-410-056-A
 A. Get Access 
R R  (1) Install the flap track fairings: 533CB, 533EB, 633CB, 633EB (Ref. TASK 57-55-11-400-004). 
R R  (2) Install the covers: 533AL, 533AR, 533AT, 533DB, 533FB, 633AL, 633AR, 633AT, 633DB, 633FB (Ref. TASK 57-55-11-400-004).
 (3) Remove the access platform(s).
 **ON A/C ALL
 Subtask 05-25-30-866-061
 B. Aircraft Maintenance Configuration
 (1) Fully retract the flaps (Ref. TASK 27-50-00-866-009).

 **ON A/C 301-399,

 TASK 05-25-30-200-008 R Zonal Inspection of the Flap Tab Hinge and Fairing No. 1A WARNING : DO NOT EXTEND THE SLATS AND FLAPS WHEN THE THRUST REVERSER COWLS ARE
_______
 DEPLOYED IN THE 45 DEG. POSITION.

 1.
 Reason for the Job

__________________
 Refer to the MPD TASK: ZL-535-01

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 3 m (9 ft. 10 in.)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-008 Extension of the Flaps on the Ground
 27-50-00-866-009 Retraction of the Flaps on the Ground
 05-25-30-991-005 Fig. 603

 3. Job Set-up
__________
 Subtask 05-25-30-866-062

 A. Aircraft Maintenance Configuration
 (1) Fully extend the flaps (Ref. TASK 27-50-00-866-008).

 Subtask 05-25-30-010-057

 B. Get Access
 (1) Put an access platform in position. 
R R  (2) Remove the access panels: 535AB, 535BB, 535CB, 635AB, 635BB, 635CB. (Ref. Fig. 603/TASK 05-25-30-991-005)
 4. Procedure_________
 Subtask 05-25-30-210-057
 A. Inspection 
R R  (1) Do a general visual inspection of the flap tab hinge and the fairing No. 1A.
 (2) Make sure that there are no signs of corrosion, cracks or damage.
 (3) Make sure that all the installations are attached correctly.
 5. Close-up________
 Subtask 05-25-30-410-057
 A. Close Access 
R R  (1) Install the access panels: 535AB, 535BB, 535CB, 635AB, 635BB, 633CB.
 (2) Remove the access platform(s).
 Subtask 05-25-30-866-063
 B. Aircraft Maintenance Configuration
 (1) Fully retract the flaps (Ref. TASK 27-50-00-866-009).

R Access Panels of the Flap Tab Hinge Fairings N. 1 R Figure 603/TASK 05-25-30-991-005
 1EFF : 301-399, 1 05-25-30Page 629 1 1 May 01/04 1 1 1CES 1

 TASK 05-25-30-200-009

R  Zonal Inspection of the Flap Tab Hinge and Fairing No. 1B WARNING : DO NOT EXTEND THE SLATS AND FLAPS WHEN THE THRUST REVERSER COWLS ARE
_______
 DEPLOYED IN THE 45 DEG. POSITION.

 1.
 Reason for the Job

__________________
 Refer to the MPD TASK: ZL-536-01

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 時間限制/維護檢查 1(78)