曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Offsets are always to be understood as a hexadecimal value. For instance, from the FSUIPC SDK the FS
Yaw Damper is defined as offset 0x808 and as a WORD has a length of 4 bytes. It is 1 when it is on and 0
when it is off.
A new button would thus look as follows:
YAW/DAMPER, 808, 4, 1, 0
When the defined value is switched on, a box is drawn around the text.
To display a value, you can use this format:
YD/####, 808, 4
Then no action will be performed, as no on/off value is defined.
Bits are defined as a period sign (.) follow by the number of the bit you want to manipulate – thus an offset
you want to use e.g. 0x5627 bit 4 is defined as:
MY/OFFSET, 5627, .4, 1, 0
Bytes have a length of 1, WORDs of 2 and DWORDs of 4.
The positioning of these commands can be controlled by additional entries such as:
page,TEST PAGE
1ST/COMM, 56F8, .0, 1, 0
2ND/COMM, 56F8, .1, 1, 0
space
3RD/COMM, 56A3, 1, 5, 0
return
4TH/COMM, 56A4, 1, 7, 2
In this case, on the page with the name TEST PAGE you would have a first row with the 1st and 2nd
commands, an empty space and then the third command… followed by a fourth one on the next line.
Editing the controls.txt file from within the program is disabled by default. If you want to enable the option,
thus getting an EDIT FILE prompt, you have to edit the pmInst.INI file and change AllowEdit from Off to
On.
The SYSTEMS/FAIL screen operates in a very similar fashion, the most important difference is that in the
CONTROLS screen, the activation of the particular command takes place immediately, a failure is controlled
by a condition such as a time delay or others…
Project Magenta Revision: 12 March-08
95
In this example, you can click on PITOT fail, and make it depend on an altitude or speed or a given delay in
seconds.
The failure then becomes active and changes its colour in the screen. To clear a failure or several failures
at the same time, you can click on CLEAR FAILURES.
You have the option to force the system to only initiate a failure when all conditions are met, i.e. the
aircraft is above a given altitude and faster than a certain speed.
The file for these commands is also in the Configs folder, called fail.txt.
Project Magenta Revision: 12 March-08
96
Instructor DATA LOGGER
The instructor station allows logging of data of various composition and in various intervals. The logged
data can be saved and loaded for later review. A wide array of data is logged as soon as you click on the
PAUSE command, it will switch into logging mode. The data is logged whether it is visible or not.
To select which colour coded data is displayed, click on the NONE entry on the left side of the graph and
select which value you want to be assigned to a particular colour. You can re-assign the value at all times.
The first three selected values are also displayed in their absolute value to the left and right of the graphs.
In some cases, such as current speed, altitude etc. the target value is shown as a dotted line (e.g. 243
knots current speed, 250 selected speed).
The sampling time can be changed by clicking on SAMPLE TIME… the choices are 5 seconds, 2s, 1s, 500
ms, 250 ms, 200 ms. You can display the complete data over time, or the last 60, 120, 180 or 300 seconds.
Please note that a large period with a high data rate may slow your system down.
Data can be saved and re-loaded via the commands, you will also be able to RESET the DATA.
The vertical line inside the graph can be seen as a cursor, the momentary value at the position of the
cursor is then shown below the graph. The X-Axis is always shows the elapsed time in seconds.
Project Magenta Revision: 12 March-08
97
Instructor APPROACH Screen
This screen will display the path during an approach, with an inset instrument display, wind speed and
component information as well as some other basic values.
A report of the approach can be generated by clicking on REPORT. To use this feature, please install the
software SVGView.exe which can be found in the /Reports subfolder. An Internet Explorer session will be
opened and the HTML file contains the graphics of the approach. The HTML file is only a background, it can
be changed in any way you wish using an HTML editor.
Project Magenta Revision: 12 March-08
98
Instructor MAP Mode
The map display has a variety of options which should be as intuitive as possible. In the Menu (Esc) you
have the option to hide the command bar when you are in pure map mode, the command bar is fixed if
you are using the instructor interface full screen.
Zoom – You can zoom by clicking on the ZOOM+/- icon, by pressing + or – on the numeric keypad or by
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Project Magenta USER MANUAL Revision: 12 March-08(30)