曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

STBY Mode (White Code Number and Mode)Figure 4-37 Standby Mode
Manualanual ON Mode
ON Mode can be selected at any time by pressing the ON Softkey. ON Mode generates Mode A and Mode S replies, but Mode C altitude reporting is inhibited. In ON Mode, a green ON indication and transponder code appear in the mode field of the Transponder Data Box.
ON Mode (No Altitude Reporting)Figure 4-38 ON Mode
124 Garmin G1000 Pilot’s Guide for the Cessna Citation Mustang 190-00494-02 Rev. B
Audio Panel and CNS
SYSTEM
OVERVIEW
FLIGHT
AUDIO PANEL EICAS INSTRUMENTS
& CNS
FLIGHT
MANAGEMENT
HAZARD
ADDITIONAL AFCS AVOIDANCE
INDEX APPENDICES FEATURES
Altitudeltitude Mode (Automaticutomaticutomatic or Manualanual)
Altitude Mode is automatically selected when the aircraft becomes airborne. Altitude Mode may also be selected manually by pressing the ALT Softkey.
If Altitude Mode is selected, a green ALT indication and transponder code appear in the mode field of the Transponder Data Box, and all transponder replies requesting altitude information are provided with pressure altitude information.
ALT Mode (Mode C Altitude Reporting)Figure 4-39 Altitude Mode
Replyeply Statustatustatus
When the transponder sends replies to interrogations, a white R indication appears momentarily in the reply status field of the Transponder Data Box.
Reply to InterrogationFigure 4-40 Reply Indication
190-00494-02 Rev. B Garmin G1000 Pilot’s Guide for the Cessna Citation Mustang 125
Audio Panel and CNS
SYSTEM
OVERVIEW
FLIGHT
INSTRUMENTS EICAS AUDIO PANEL
& CNS
FLIGHT
MANAGEMENT
HAZARD
AVOIDANCE AFCS ADDITIONAL
FEATURES APPENDICES INDEX
Entering a Transponder Code
Entering a transponder code with softkeys:
1) Press the XPDR Softkey to display the Transponder Mode Selection Softkeys.
2) Press the CODE Softkey to display the Transponder Code Selection Softkeys, for digit entry.
3) Press the digit softkeys to enter the code in the code field. When entering the code, the next softkey in sequence must be pressed within 10 seconds, or the entry is cancelled and restored to the previous code. Pressing the BKSP Softkey moves the code selection cursor to the previous digit. Five seconds after the fourth digit has been entered, the transponder code becomes active.
Entering a CodeFigure 4-41 Entering a Code with Softkeys
Entering a transponder code with the PFD FMS Knob:
1) Press the XPDR and the CODE Softkeys as in the previous procedure to enable code entry.
2) Turn the small FMS Knob to enter the first two code digits.
3) Turn the large FMS Knob to move the cursor to the next code field.
4) Enter the last two code digits with the small FMS Knob.
5) Press the ENT Key to complete code digit entry.
Pressing the CLR Key or small FMS Knob before code entry is complete cancels code entry and restores the previous code. Waiting for 10 seconds after code entry is finished activates the code automatically.
Figure 4-42 Entering a Code with the FMS KnobPress the ENT Key to Complete Code EntryTurn the Large FMS Knob to Move the Cursor to the Next Code FieldTurn the Small FMS Knob to Enter Two Code Digits at a Time
126 Garmin G1000 Pilot’s Guide for the Cessna Citation Mustang 190-00494-02 Rev. B
Audio Panel and CNS
SYSTEM
OVERVIEW
FLIGHT
AUDIO PANEL EICAS INSTRUMENTS
& CNS
FLIGHT
MANAGEMENT
HAZARD
ADDITIONAL AFCS AVOIDANCE
INDEX APPENDICES FEATURES
VFR Code
The VFR code can be entered either manually or by pressing the XPDR Softkey, then the VFR Softkey. When the VFR Softkey is pressed, the pre-programmed VFR code is automatically displayed in the code field of the Transponder Data Box. Pressing the VFR Softkey again restores the previous identification code.
The pre-programmed VFR Code is set at the factory to 1200. If a VFR code change is required, contact a Garmin-authorized service center for configuration.
Figure 4-43 VFR CodeVFR Code
IDENT Function NOTE: In Standby Mode, the IDENT Softkey is inoperative.
Pressing the IDENT Softkey sends a distinct identity indication to Air Traffic Control (ATC). The indication distinguishes the identing transponder from all the others on the air traffic controller’s screen. The IDENT Softkey appears on all levels of transponder softkeys. When the IDENT Softkey is pressed, a green IDNT indication is displayed in the mode field of the Transponder Data Box for a duration of 18 seconds.
After the IDENT Softkey is pressed while in Mode or Code Selection, the system reverts to the top-level softkeys.
Press the IDENT Softkey to Initiate the ID FunctionIDNT IndicationFigure 4-44 IDENT Softkey and Indication
190-00494-02 Rev. B Garmin G1000 Pilot’s Guide for the Cessna Citation Mustang 127
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Cessna Citation Mustang Pilot’Guide 1(51)