曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

heel of the aeroplane and the edge of the tariway should be & high, a wheel-to-edge clearance greater than 4.5 m may be
not less than that given by the following tabulation: provided to permit higher taxiing speedr.
Code letter Clearance
A 1.5 m
B 2.25 m
C 3 m ifthe taxiway is intended to be
wed by aeroplanes with a wheel
base Iess than 18 m;
4.5 m ifthe taxiway is intended to be
used by aeroplanes with a wheel
base equal to or greater than 18 m.
D 4.5 m
E 4.5 m
F 4.5 m
Note 1.- Wheel base means the distance fmm the nose
gear to the geometric centre of the main gear.
Note 2.- Where the code letter is F and the trafic density
is high, a wheel-to-edge clearance greater than 4.5 m may be
provided to pennit higher taxiing speedr.
3.9.4 As of 20 November 2008, the design of a taxiway
shall be such that, when the cockpit of the aeroplane for which
the taxiway is intended remains over the taxiway cenhe line
markings, the clearance distance between the outer main wheel
of the aeroplane and the edge of the taxiway shall be not less
than that given by the following tabulation:
3.9.5 Recommendation.- A straight portion of a taxiway
should have a width of not less than that given by the
following tabulation:
Code letter Taxiway width
C 15 m ifthe taxiway is intended to
be used by aeroplanes with a wheel
base Iess than 18 m;
I8 m ifthe taxiway is intended to
be used by aeroplanes with a wheel
base equal to or greater than 18 m.
I8 m $the taxiway is intended to
be used by aeroplanes with an
outer main gear wheel span of less
than 9 m;
23 m ifthe taxiway is intended to
be used by aeroplanes with an
outer main gear wheel span equal
to or greater than 9 m.
24111105
No. 7
Annex 14 -A er~dromes V@f~mIe
--.,"----
--------
The figure shows an emm@e of tm&ay widening to achieve
the spified whed clmmm taxiway curves (see 3.9.6).
Guime maten'al on witaMe dimsim is $vw in the
Aerdme &&gn Mmoal, Part 2.
Figure 3-2. Taxiway curve
Note.- Guidance on width of tmiways is given in the
Aerodrome Design Manual, Part 2.
3.9.6 Recommendation, Changes in direction of
tmiways should be as feu, and small as possible. The radii of
the curves should be compatible tyith the manoeuwing
capabili~a nd normal faiing speedr of the aeroplanes for
which the taxiway is intended. T%e design ofthe curve should
be such that, when the cockit ofthe aeroplane remains over
the taxiway centre fine markings, the clearance dktance
beween the outer main wheels ofihe aeroplane and the edge
offhe taxiway should not be iess than those speciJed in 3.9.3.
Junctions and intersections
3.9.7 Recommendation.- To facilitate the movement of
aeroplanes, fillets should be provided at junctions and
intersections of tmiwqs with mnwqs, aprons and other
~ m ~ q71s1e .d esign of the fillets should ensure that the
minimum wheel clearuncm speczFed in 3.9.3 are maintained
when aeroplanes are manoeuwing through the junctions or
intersect ions.
Note.- Consideration will have to be given to rhe
aeroplane datum length d e n designing fillets. Guidance on
the design of$Zlets and the de$~ifion ofthe tem amplane
dahrm length are given in the Aerodrome Design Mmuai,
Part 2.
Note 1.- An example oftvidening taxiways to achieve the
wheel clearance specz$ed is ilImtrafed in Figure 3-2. Taiway separation disiances
Guidance on the values ofsuitable dimensions is give8 in the
Aerodrome Deslgn Manual, Part 2. 3.9.8 Recommendation;-- The separation distance
2.- The locution oftm.waJt centre line and tfE cmpe h e of a fmiwq and the centre fine of a
lights is speczfied in 5.2.8.4 and 5.3.15.11. m w y , the centre line of a parallel ta-viwq or an o b w
should not be Iess than the appropriate ddmension spec1jr;ed in
Note 3.- Conrpound cumes mnqi reduce or elinzirzafe 8he Table 3-1, except that ~t mq be pemissible to operafe m'th
needfor tmiway width. lower separation distances at an asristing aerodrome i f an
24/11/05
No. 7
Chapter 3
Table 3- 1. Taxiway minimum separation distances
Distance between taxiway centre line Taxiway.
and runway centre line (metres) other than
Taxiway aircraft stand Air& stand
Instrument runways Non-instrument runways centre line taxilane, taxilane
Code
Code number
letter I 2 3 4
Code number
to taxiway centre line centre line
centre line to obiect to obiect
1 2 3 4 (metres) (metres) (me&)
Note I.- The separation distances shown in columns (2) to (9) represent ordinary combinations of runways and taxiways. The
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：附件14-機場 Aerodromes an14_v2_2ed(46)