曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費(fèi)者

ALL  appet Socket ody (Hyperbolic) .007L .009L
514 537 ALL Camshaft
and Crankcase  .002L .004L .006L
515 538 Camshaft  .002L
ALL amshaft -End Clearance .009L .015L
516 539 ALL Camshaft
Run-Out At Center .000 BearingJournal .001 .006
517 578 ALL  Counterweight
Bushing and .0013T Crankshaft
.0026T (A)
518 579 ALL Counterweight
Roller -End .007L earance .025L .038L
519 580 ALL  Counterweight
and Crankshaft -.003L de Clearance* .013L .017L
* Measure below roller next to flat.
520 696 ALL Counterweight
Bore and .0002L Washer
asher O.D.
.0030L (A)
ALL D.of Counterweight Bushing
.7505 .7512
521 775 I.D.  .7485
522 774 ALL  0. .D. of Counterweight Roller (PP/N69433) (See latest edition .5045 of Service Instruction No. 1012) .5050
AC 0. D. of Counterweight Roller
P/N 73287) (See latest edition .5189
of Service Instruction No. 1012) .5194

ALL  0.
D. of Counterweight Roller
P/N70416) (See latest edition .6945 of Service Instruction No. 1012) .6950
523 503 ALL Thrust
Bearing and Propeller .0000 Shaft .0012L.002L2L
526 509 ALL  ThThrustBearing and Thrust Bearing .0031 CaCapClamp Fit (Shim to This Fit) .005TT (A)
527 555 ALL  Th
ThrustBearing Tilt  .027 Tilt
3-2
SERVICE TABLE OF LIMITS PART III GEARED ENGINES
SECTIONI CRANKCASE, CRANKSHAFT,CAMSHAFT
Ref.
New

528 530 531
535 536
536
537
538 539 540
541
Ref.
Old

555
505 506
-570 571
571
573
Chart
ALL ALL ALL
ALL ALL
ALL
ALL
575:ALL
577 ALL 900 P-AB-AC
718 H4-H5-P-AB-AC
Nomenclature
Thrust Bearing -End Play
Propeller Shaft Run-Out
(Rear Cone Location)
Propeller Shaft Run-Out
(Front Cone Location)
(Propeller Shaft Installed)
Starter Jaw and Crankshaft
Thrust Bearing and Reduction
Gear Housing
Crankshaft and Crankcase
Front Bushing
Pinion -End Clearance
Pinion Shaft and Cage (See
latest edition of Service
Instruction No. 1236)
Pinion Shaft and Cage (See
latest edition of Service
Instruction No. 1114)
Propeller Shaft and Crankshaft Bushing
I.D. Propeller Shaft Bushing In Crankshaft
Stationary Gear and Plate -End Clearance
Ring Gear and Drive Plate -End Clearance
Reduction Gear Governor and Magneto Housing and Reduction Gear Housing Sleeve
Rear Crankshaft Spline Bushing and Crankshaft .006 .008 .010
Dimensions  Clearance 
Mfr.  Mfr. 
Min.  Serv.  Min.  Serv. 
&  Max.  &  Max. 
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Lycoming SERVICE TABLE OF LIMITS AND TORQUE VALUE RECOMMENDATIONS(34)