(5)
Connect the multimeter to the squib test box.
S 865-107
(6)
Set the LOAD CHECK switch on the squib circuit test box to the ON position.
S 485-106
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
26-21-00
ALL ú ú 02 Page 506 ú Jan 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL
S 865-108
(7) On the ENGINE FIRE Control Panel, P8, pull the LEFT engine fire handle out to the emergency fire position.
NOTE: When you pull the fire handles into the emergency fire
____ position, it is necessary to use the manual fire override switch behind the fire handle. When you turn the fire handles, it is necessary to hold the handles against the stops while the voltage is measured.
(a)
Make sure the EICAS message, L ENG SHUTDOWN, shows on the top display.
(b)
Make sure the BOTTLE DISCHARGE light on the squib circuit test box stays off.
(c)
Make sure the multimeter on the squib circuit test box shows 0 |2 volts.
S 865-114
(8) Turn and hold the LEFT engine fire handle fully counterclockwise to the DISCH 1 position.
(a)
Make sure the BOTTLE DISCHARGE light on the squib circuit test box comes on.
(b)
Make sure the multimeter on the squib circuit test box shows 16 volts minimum.
NOTE: If voltage is less than 16 volts, the circuit may not
____ give sufficient current to fire the squib.
S 865-111
(9) Open this circuit breaker on the P6 panel:
(a) 6H1, FIRE EXTINGUISHING ENG L BTL 1
S 765-110
(10)
Make sure the BOTTLE DISCHARGE light on the squib circuit test box goes off.
S 765-109
(11)
Make sure the multimeter on the squib circuit test box shows 0 |2 volts.
S 865-127
(12)
Close this circuit breaker on the P6 panel:
(a) 6H1, FIRE EXTINGUISHING ENG L BTL 1
S 215-153
(13) Make sure the BOTTLE DISCHARGE light on the squib circuit test box comes on.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
26-21-00
ALL ú ú 13 Page 507 ú Sep 28/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL
S 215-154
(14) Make sure the multimeter on the squib circuit test box shows 16 volts minimum.
NOTE: If voltage is less than 16 volts, the circuit may not give
____
sufficient current to fire the squib.
S 745-126
(15) Release the LEFT engine fire handle.
(a)
Make sure the fire handle moves quickly toward center about 10 degrees.
(b)
Make sure the BOTTLE DISCHARGE light on the squib circuit test box goes off.
(c)
Make sure the multimeter on the squib circuit test box shows 0 |2 volts.
S 865-125
(16)
Set the LOAD CHECK switch on the squib circuit test box to the OFF position.
S 025-124
(17)
Disconnect the bottle 1 left engine squib connector, D2188, from the squib test box adapter cable.
S 425-123
(18)
Connect the bottle 2 left engine squib connector, D2268, to the squib test box adapter cable.
S 865-122
(19)
Set the LOAD CHECK switch on the squib circuit test box to the ON position.
S 865-121
(20)
Turn and hold the LEFT engine fire handle fully clockwise to the DISCH 2 position.
(a)
Make sure the BOTTLE DISCHARGE light on the squib circuit test box comes on.
(b)
Make sure the multimeter on the squib circuit test box shows 16 volts minimum.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 防火 FIRE PROTECTION 2(13)
