S 024-017

 (6)
Remove the clutch pack assembly (1) from the frame assembly.

 TASK 22-32-05-004-018
 3. Remove an Autothrottle Clutch Assembly (Fig. 401)
______________________________________
 A. Access
 (1)  Location Zones
 113/114 Area Forward of NLG Wheel Well

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-32-05
 ALL  ú ú 02 Page 404 ú Dec 20/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757 MAINTENANCE MANUAL
 (2)  Access Panel 113AL Flight/Landing Gear/Engine Control Components
 B. Remove an Autothrottle Clutch Assembly
 S 014-032
 (1)  
Remove the autothrottle clutch pack assembly (1).

 S 034-019

 (2)  
Remove the nut (11) from the end of the clutch pack assembly shaft (15).

 S 034-020

 (3)  
Remove the support bracket (12) from the clutch pack assembly shaft (15).

 S 034-021

 (4)  
Remove the spacer (13, 14) from the clutch pack assembly shaft (15).

 S 024-022

 (5)  
Remove the clutch assembly (16) from the clutch pack assembly shaft (15).

 TASK 22-32-05-404-023
 4. Install an Autothrottle Clutch Assembly (Fig. 401)
_______________________________________
 A. Equipment
 (1)  Torque Rack - A22003-23
 B. Parts
 ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT |FIG | ITEM | ................................................................................ | 401 | 1 | Clutch Pack Assembly | 22-32-51 | 05 | 202 | | | 11 | Nut | | | 210 | | | 12 | Support Bracket *[1] | | | | | | 13 | Spacer | 22-32-51 | 05 | 206 | | | 14 | Spacer | | | 205 | | | 15 | Clutch Pack Assembly Shaft | | | 207 | | | 16 | Clutch Assembly | | | 212 | | | 16 | Clutch Assembly | | | 214 | 2......…........…...................................…............…....…........1 *[1] Refer to CMM 22-32-25.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-32-05
 ALL  ú ú 02 Page 405 ú May 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

 C. Access
 (1)  
Location Zones
 113/114 Area Forward of NLG Wheel Well

 (2)  
Access Panel 113AL Flight/Landing Gear/Engine Control Components

 D. Install Autothrottle Clutch Assembly
 S 424-024
 (1)  Install the clutch assembly (16) on the clutch pack assembly shaft (15).
 (a)  Make sure that the clutch assembly (16) is aligned with the center spacer (14).
 S 434-025
 (2)
Install the spacer (13) on the clutch pack assembly shaft (15).

 S 434-026

 (3)  
Install the support bracket (12) on the clutch pack assembly shaft (15).

 S 434-027

 (4)  
Install a new nut (11) to the end of the clutch pack assembly shaft (15).

 S 824-029

 (5)  
Hold the clutch pack assembly (1) on a torque rack, and tighten the nut (11) to 200-220 in-lbs more than run-on torque.

 NOTE:____We recommend you replace the nut. The nut is a locknut with a nylon locking device. The run-on torque measured during locknut installation can be lower when you use the nut again.
 S 414-030
 (6)  
Install the autothrottle clutch pack assembly (1).

 (7)  
Do a test of the autothrottle clutch pack assembly.

 S 714-031
 TASK 22-32-05-404-033
 5. Install the Autothrottle Clutch Pack Assembly (Fig. 401)
_____________________________________________
 A. Equipment
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 自動飛行 AUTOFLIGHT 2(148)