曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 WARNING: DO NOT BREATHE THE VAPORS OF THE SOLVENTS OR ETCH SOLUTIONS.
_______ DO NOT GET THEM IN YOUR EYES, ON YOUR SKIN OR ON YOUR CLOTHES. INJURY TO PERSONS MAY OCCUR.
 (2)  This inspection will usually occur on the components of the landing gear axles. The signs of discolored or blistered paint or plating shows that a general intense heat has changed the temper of the axle. When this happens, the ammonium persulphate procedure should be applied to the damaged part of the axle. Do this procedure after the axles have been reworked. Axle rework procedures can be found in Chapter 32, Landing Gear.
 B. Consumable Materials
 (1)  
Air - Clean, dry, compressed

 (2)  
Ammonium persulphate etch solution

 (a)  100 grams of ammonium persulphate per 0.27 gallon of tap water

 (3)  
Methyl or Isopropyl Alcohol - TT-1-735 (Ref 20-30-02)

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 05-51-14
 ALL  ú ú 05 Page 207 ú Dec 20/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL

 (4)  
G00034 Cheesecloth

 (5)  
Brushes

 (6)  
B00183 Trichloroethylene Solvent - BMS 11-6, types I and II

 (7)  
G00270 Masking tape

 (8)  
B00168 Wet and Dry Abrasive Paper - Number 400 or finer

 C. References
 (1) 32-45-01, Main Gear Wheel Well and Tire - Removal/Installation
 D. Ammonium Persulphate Solution Procedure
 S 122-043
 WARNING: DO NOT BREATHE THE VAPORS OF THE SOLVENTS OR ETCH SOLUTIONS.
_______ DO NOT GET THEM IN YOUR EYES, ON YOUR SKIN OR ON YOUR CLOTHES. INJURY TO PERSONS MAY OCCUR.
 (1)  
Strip the cadmium surface with sandpaper applied by hand. Strip a minimum area of 0.5 inch through the area that is not to be tested.

 S 112-034

 (2)  
Clean the area to be etched, with solvent.

 S 282-035

 (3)  
Apply the ammonium persulphate solution, with a cheesecloth, on the surface to be tested for 30 to 60 seconds.

 S 162-042
 WARNING: DO NOT LET THE ETCHANT SOLUTION TOUCH THE CADMIUM PLATED
_______ SURFACES. POISONOUS FUMES CAN OCCUR AND CAUSE INJURY TO PERSONS.
 (4)  
Rinse the surface with hot or cold water immediately. Alcohol can also be used.

 S 162-037

 (5)  
Dry the surface with clean, dry compressed air immediately.

 E. Examine etched area.
 S 212-038
 (1)  Examine the parts with a bright light and without magnification. Look for signs of burning.
 (a)  
If all of the etched area is the same shade of gray, there will be no change to the temper of the steel.

 (b)  
The area that has been too hot will be light in color. Look for the light color in the center of a darker area.

 (c)  
If the etched area is mottled, the condition of the heat treat is not sure. Replace the axle or do a high quality metallurgical test.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 05-51-14
 ALL  ú ú 04 Page 208 ú Dec 20/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757 MAINTENANCE MANUAL
 F. Put the airplane back to its usual condition.
 S 122-039
 (1) Remove the etch with abrasive paper.
 NOTE:____Do this step if the part is serviceable. If it is not serviceable, install replacement parts.
 S 372-040
 (2)
Refinish the surface with the correct primer and paint.

 S 422-041

 (3)
Install replacement tires and wheels (Ref 32-45-01).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 05-51-14
 ALL  ú ú 02 Page 209 ú Dec 20/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 時間限制/維護檢查(21)