EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 80-11-02
 ALL  ú ú N05 Page 404 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
D. Access
 (1)  
Location Zone
 412 Engine No. 1
 422 Engine No. 2
 432 Engine No. 3
 442 Engine No. 4

 (2)  
Access Panel
 415 and 416 Thrust Reverser Halves - Engine No. 1
 425 and 426 Thrust Reverser Halves - Engine No. 2
 435 and 436 Thrust Reverser Halves - Engine No. 3
 445 and 446 Thrust Reverser Halves - Engine No. 4

 E. Procedure
 S 434-016-N00
 (1)  
Remove the dust caps.

 S 214-017-N00

 (2)  
Examine the flange seal surfaces and seal (4) for scratches, cracks, and other unwanted conditions.

 (a)  Replace the seal, if it is necessary.
 S 424-041-N00
 (3)  Do these steps to install the start valve (Fig. 401):
 NOTE: You can get access to the manual override in the starter
____ valve through the access hole in the left core cowl only when the starter, interconnect duct, and starter valve are correctly aligned.
 (a)  Clean the mating flanges between the interconnect duct (5) and the start valve (2).
 NOTE: This will make sure there is an electrical bond between
____
 the mating flanges.

 (b)  
Install the seal (4) on the flange.

 (c)  
Align the start valve (2) with the lower start duct.

 NOTE: Make sure the separation between the flanges is no
____ more than 0.03 inch (0.76 mm).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 80-11-02
 ALL  ú ú N05 Page 405 ú Oct 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
(d)  Install the coupling (3) on the flanges.
 (e)  Tighten the coupling nut with the hand.
 (f)  Do these steps to install the interconnect duct (5), if
 necessary:
 1) Examine the flange seal surfaces (where the innterconnect
 duct and the starter touch) and seal (4) for scratches,
 cracks, and other unwanted conditions.
 a) Replace the seal, if it is necessary.
 2) Install the seal (4) on the flange.
 3) Put the interconnect duct (5) between the starter and the
 start valve (2).
 a) Align the index key on the duct flange with the index
 hole in the starter flange.
 b) Make sure the separation between the flanges is no more
 than 0.03 inch (0.76 mm).
 4) Install the couplings (3) on the flange connection.
 a) Tighten the coupling nut to 100-115 pound-inches (11-13
 newton meters).
 (g)  Examine the flange seal surfaces (where the interconnect duct
 and start valve touch) and seal (4) for scratches, cracks, and
 other unwanted conditions.
 1) Replace the seal, if it is necessary.
 (h)  Install the seal (4) on the flange.
 (i)  Align the index hole in the duct flange with the index key in
 the start valve flange.
 1) Make sure the separation between the flanges is no more
 than 0.03 inch (0.76 mm).
 (j)  Install the couplings (3) on the flange connection.
 1) Tighten the coupling nut to 100-115 pound-inches (11-13
 newton meters).
 (k)  Tighten the coupling (3) nut between the start valve and the
 lower starter duct to 100-115 pound-inches (11-13 Newton
 meters).
 (l)  Clean the mating surfaces between the bonding jumper (9) and
 the start valve (2).
 NOTE: This will make sure there is an electrical bond between____
 the mating surfaces.
 (m)  Install the screw (8), washers (7), and nut (6) that attach the
 bonding jumper (9) to the start valve (2) flange
 (AMM 20-11-15/401).
 (n)  Do a check of the electrical bonding resistance
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起動 STARTING(15)