75-24-02
 ALL  ú ú N01 Page 417 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
D. Access
 (1)  
Location Zone
 412 Engine 1 - Aft HPC Case to Fwd HPT Case
 422 Engine 2 - Aft HPC Case to Fwd HPT Case
 432 Engine 3 - Aft HPC Case to Fwd HPT Case
 442 Engine 4 - Aft HPC Case to Fwd HPT Case

 (2)  
Access Panel
 416 Right Thrust Reverser Half - Engine 1
 426 Right Thrust Reverser Half - Engine 2
 436 Right Thrust Reverser Half - Engine 3
 446 Right Thrust Reverser Half - Engine 4

 E.
Procedure

 S 424-170-N00
 (1)  
Install the No.2 turbine-vane cooling air-duct:

 (a)  
Remove the protection caps from the TVC air duct, HPT case opening, and TVBCA valve port.

 (b)  
Attach a new gasket to the TVBCA valve flange with paraffin wax.

 (c)  
ENGINES WITHOUT PHASE 3 CHANGES PRE-PW-SB 72-315 OR PRE-PW-SB 75-57; Attach a new metering orifice seal plate, convex side out, to the HPT pad where the rear flange of the TVCA duct goes.

 (d)  
ENGINES WITH PHASE 3 CHANGES OR POST-PW-SB 72-315 OR POST-PW-SB 75-57; Attach a new gasket on the HPT pad where the rear flange of the TVCA duct goes.

 (e)  
Lubricate the threads of the bolts, which attach the TVC air duct and brackets, with engine oil.

 (f)  
Attach the TVC air duct and brackets to the pads on the TVBCA valve port and on the HPT case with the bolts. 1) Use the larger bolts on the aft flange. 2) Tighten the bolts with your hand.

 (g)  
Lubricate the threads of the bolts, which attach the clamp on the TVC air duct, with engine oil.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 75-24-02
 ALL  ú ú N06 Page 418 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(h)  
Attach the clamp on the TVC air duct to the bracket on the flange M with the bolts and nuts. 1) Tighten the bolts to 85-95 pound-inches (9.6-10.7

 newton-meters).

 (i)  
Tighten the bolts, from one corner to the opposite corner, at the forward flange to 85-95 pound-inches (9.6-10.7 newton-meters). 1) Without loosening, tighten the bolts again until the

 necessary torque is kept.

 (j)  
Tighten the bolts, from one corner to the opposite corner, at the aft flange to 180-200 pound-inches (20.3-22.6 newton-meters). 1) Without loosening, tighten the bolts again until the

 necessary torque is kept. 2) Safety the bolts with lockwire or safety cable and safety cable ferrule.

 (k)  
Install the accessory cooling air tube and the tube support bracket with the steps that follow: 1) Lubricate the threads of the bolts, which attach the

 support bracket for the accessory cooling air tube, with engine oil. 2) Install the support bracket to the flange M and flange N
 support brackets with the bolts, washers, and nuts. 3) Tighten the bolts. 4) Put the accessory cooling air tube on the HPT case. 5) Lubricate the threads of the screw, which attaches the tube
 clamp for the accessory cooling air tube, with engine oil. 6) Attach the tube clamp to the support bracket on the flange
 M and flange N support brackets with the screw and washer. 7) Tighten the screw. 8) Connect the tube nut to the inlet duct for the turbine case
 cooling air. 9) Tighten the tube nut. 10) Connect the tube nut at the forward end of the tee on the
 accessory cooling air tube. 11) Tighten the tube nut. 12) Lubricate the threads of the bolts, which attach the clamp
 on the lower end of the accessory cooling air tube, with engine oil.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 75-24-02
 ALL  ú ú N06 Page 419 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
13) Attach the clamp on the lower end of the accessory cooling
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 大氣 AIR 1(60)