NOTE: You can use the PWA 85749 Adapter to loosen the electrical
____
 connectors.

 (a)  Install the protection caps on the open ends of the electrical connectors.
 S 034-008-N00
 (13)
 Remove the bolts (18, 20) which attach the ends of the cable for the stator (17) and the retaining plate (21) to the bracket.

 S 034-029-N00

 (14)
 Remove the retaining plate (21) and the ends of the cable for the stator (17) from the bracket.

 S 034-070-N00

 (15)
 Disconnect the cables for the stator (17) from the spring clips around the IDG drive pad.

 S 034-009-N00

 (16)
 Loosen the hose clamp (13) for the cooling air tube (14) located on the right side of the stator (17).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 73-21-05
 ALL  ú ú N03 Page 409 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
S 034-030-N00
 (17)
 Disconnect this cooling air tube (14) from the stator (17).

 S 034-069-N00

 (18)
 ENGINES POST-PW-SB 72-375;
 Do these steps:

 (a)  
Loosen the hose clamp (13) for the cooling air tube (14) located at the bottom of the stator (17).

 (b)  
Remove the bolts and/or nuts from the clamps that attach the cooling air tube to the brackets on the gearbox, oil tank, and diffuser case.

 (c)  
Move the tube away from the EEC alternator.

 NOTE: The clamps can stay with the tube.
____
 (d)  
Remove the bolts (11) and washer (19) which attach the stator (17) to the EEC alternator drive pad.

 (e)  
Remove the stator (17) from the gearbox.
 1) Discard the packing (15).

 S 034-068-N00
 (19)
 ENGINES PRE-PW-SB 72-375;
 Do these steps:

 (a)  
Remove the bolt (18) which attaches the clamp (16) on the stator cable to the bracket on the right side of the stator.

 (b)  
Remove the clamp (16) from the cable for the stator (17).

 (c)  
Remove the bolts (11) and washer (19) which attach the stator (17) and the heat shield (12) to the EEC alternator drive pad.

 (d)  
Remove the stator (17) and the heat shield (12) from the gearbox. 1) Discard the packing (15).

 S 034-014-N00
 (20) Install the protection cap on the EEC alternator drive pad and the open end of the stator (17).
 TASK 73-21-05-004-015-N00
 3. Remove the EEC Alternator (N2 Transducer) Rotor (Fig. 403)
_______________________________________________
 A. Special Tools and Equipment
 (1)  
PWA 85238 - Wrench holder (Engines PRE-PW-SB 72-375),
 Pratt & Whitney, Commercial Products Division,
 400 Main Street, East Hartford, CT 06108

 (2)  
PWA 86603 - Adapter, Wrench (Engines POST-PW-SB 72-375),
 Pratt & Whitney

 (3)  
PWA 85931 - Puller (Engines PRE-PW-SB 72-375), Pratt & Whitney

 (4)  
PWA 86551 - Puller (Engines POST-PW-SB 72-375), Pratt & Whitney

 B.
References

 (1)  
IPC 72-61-05 Fig. 1

 (2)  
IPC 73-21-05 Fig. 5

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 73-21-05
 ALL  ú ú N03 Page 410 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
PWA 85238 
WRENCH  1  SEE  A  ADAPTER PWA 86603 2  SEE  A 
BODY  BODY 
JAM NUTS  JAM NUTS 
EEC  EEC 
ALTERNATOR  ALTERNATOR 
DRIVE PAD  DRIVE PAD 

THREADED  THREADED 
SHAFT  BOLT  HANDLE  SHAFT  BOLT  HANDLE 
(3 LOCATIONS)  (3 LOCATIONS) 
2.  LOCK RING 
THREADED  1. NUT 
SHAFT 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 發動機燃油和控制 2(25)