S 018-010-N00
(3)
Open the core cowl panel (AMM 71-11-06/201).
S 018-011-N00
WARNING: OBEY THE INSTRUCTIONS IN AMM 78-31-00 WHEN YOU OPEN THE THRUST
_______ REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS, INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR.
(4)
Open the thrust reversers (AMM 78-31-00/201).
S 028-002-N00
(5)
Do this task: "Remove An Intermediate Case Fairing" (AMM 72-34-05/401).
S 328-003-N00
(6)
Put rivet holes in the new fairing (Fig. 801 and 802).
(a)
Put the new fairing on the strut so that the edge gap is approximately equal on all sides. 1) The difference between each edge gap dimension must be less
than 0.030 inch (0.762 mm). 2) Make the gap at the outer diameter edge smaller if the new fairing does not have an overlap there.
(b)
Use applicable clamps to hold the new fairing in the correct
position.
(c)
Make a mark on the new fairing where the five used rivet holes on the strut are.
(d)
Remove the new fairing from the strut.
(e)
Make marks for the nine new rivet holes that are necessary.
CAUTION: DO NOT USE FLUIDS OR LUBRICANTS WHEN YOU MACHINE THE RIVET
_______ HOLES. BE CAREFUL TO PROTECT THE MACHINED SURFACES FROM CONTAMINATION. IF YOU DO NOT PROTECT THE MACHINED SURFACES YOU CAN CAUSE DAMAGE TO THE LAMINATION.
(f)
Machine the nine new rivet holes through the new fairing.
(g)
Machine the five rivet holes vertically through the new fairing where the five used rivet holes are in the strut.
S 328-004-N00
(7)
Use the limits in figure 802 to machine rivet holes through the strut.
(a)
Put the new fairing in the correct position on the strut.
(b)
Use clamps to hold the new fairing in the correct position.
(c)
Machine nine new rivet holes through the new fairing again and in the strut.
(d)
Remove the new fairing.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-34-05
ALL ú ú N01 Page 802 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
A SEE A
INTERMEDIATE CASE STRUT
INTERMEDIATE CASE FAIRING (2 ON EACH STRUT)
A
EDGE GAP AROUND THE FAIRING CONTOUR FAIRING CONTOUR STRUT SPACE
THE FAIRING MUST HAVE AN OVERLAP ON THE STRUT
RIVET HOLES THAT RIVET HOLES THAT
ARE NOT USED IN ARE USED IN
THE REPAIR THE REPAIR
A-A L-A6453
Intermediate Case Fairing
Figure 801
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-34-05
ALL ú ú N01 Page 803 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES /MAINTENANCE MANUAL ////////////////////////
L-A6453 Limits for the Installation of the Fairings Figure 802 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-34-05
ALL ú ú N01 Page 804 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
BOND ALL AROUND
NO CONTROL IS NECESSARY
RIVETS L-A6590 L-A6678 Limits for the Installation of the FairingsFigure 802 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 發動機 ENGINE 2(80)
