gouges, or cracks
 4) No more than three in a 45 degree arc.

 (c)  
If damage is worse than those limits, replace the fan exit fairing (AMM 72-31-03/401).

 (d)  
Compare the delamination you find on the composite material with the limits that follow. 1) Not more than 1.00 inch (25.40 mm) by 1.50 inches (38.10

 mm) in dimension 2) Not more than 0.05 inch (1.27 mm) in depth 3) A minimum of 2.00 inches (50.80 mm) away from other
 delamination, nicks, or gouges 4) No more than 5 nicks, delaminations, or gouges in a 45 degree arc.
 (e)  
If the delamination is less than those limits, examine the delamination after each 50 hours for increased dimensions.

 (f)  
If the delamination is worse than those limits, replace the fan exit fairing before the 26th hour (AMM 72-31-03/401).

 (g)  
If the delamination is more than 2.50 inches (63.50 mm) by 2.00 inches (50.80 mm), replace the fan exit fairing (AMM 72-31-03/401).

 S 226-005-N00
 (5)  
Examine Area B, the surface of the fan exit fairing, for damage.

 (a)  
Nicks, and gouges that are in the limits that follow are permitted: 1) No more than 1.00 inch (25.40 mm) diameter, 2) No more than 0.05 inch (1.27 mm) in depth, 3) A minimum of 2.00 inches (50.80 mm) away from other nicks,

 or gouges,
 4) No more than five in a 45 degree arc.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 72-31-03
 ALL  ú ú N01 Page 603 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
(b)  
If damage is worse than those limits, replace the fan exit fairing (AMM 72-31-03/401).

 (c)  
Compare the delamination you find on the composite material with the limits that follow. 1) Not more than 1.00 inch (25.40 mm) by 1.50 inches (38.10

 mm) in dimension 2) Not more than 0.05 inch (1.27 mm) in depth 3) A minimum of 2.00 inches (50.80 mm) away from other
 delamination, nicks, or gouges 4) No more than 5 nicks, delamination, or gouges in a 45 degree arc.
 (d)  
If you find some delamination but it is less than those limits, examine the delamination after each 50 hours for increased dimensions.

 (e)  
If the delamination is worse than those limits, replace the fan exit fairing before the 26th hour (AMM 72-31-03/401).

 (f)  
If the delamination is more than 2.50 inches (63.50 mm) by 2.00 inches (50.80 mm), replace the fan exit fairing (AMM 72-31-03/401).

 S 216-006-N00
 (6)  Examine the black polyurethane surface layer of areas A and B for damage.
 NOTE: Fan exit fairings that have a steel cap on the leading edge
____
 will not have the black polyurethane surface layer.

 (a)  
Delamination, erosion, or loose areas of the black polyurethane surface layer is permitted on 100 percent of the surfaces.

 (b)  
On engines with a steel cap on the leading edge, visually examine the steel cap to make sure it is correctly attached.

 (7)  
Remove the protective mats from the inlet cowl.

 (8)  
Remove the DO-NOT-OPERATE tags from the fuel control switches.

 S 096-007-N00
 S 866-008-N00
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 72-31-03
 ALL  ú ú N01 Page 604 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
1ST-STAGE STATOR - REMOVAL/INSTALLATION
_______________________________________
 1.  General_______
 A.  The procedure that follows gives the tasks for the removal and the
 installation of the 1st-stage stator.

 B.  The 1st-stage stator is the first stage of the low pressure compressor
 (LPC) and is an annular flange which holds the stator vanes.

 C.  The 1st-stage stator is immediately aft of the 1st-stage fan blades . It is the start of the LPC.
 D.  To get access to the 1st-stage stator, you must go into the inlet cowl,
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 發動機 ENGINE 1(173)