曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (5)  Install The Bearing.
 (a)  Install the bearing such that you can see the manufacturers number unless it is differently specified.
 NOTE: When you install a roller bearing, turn the rollers
____ in the relation to the outer race. This will make the incorrect operation of the rollers less possible. This will also help you to find an incorrect operation of the rollers.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 70-24-04
 ALL  ú ú N01 Page 202 ú Oct 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
CAUTION:_______ THE LARGE SPANNER NUTS FREQUENTLY HAVE SMALL BURRS AT THE
 SPANNER SLOTS.  THESE NUTS ATTACH THE MAIN BEARINGS OR THE
 SEALS TO THE SHAFTSAND HOUSINGS.  DO NOT INSTALL A SPANNER
 NUT REARWARD.  THIS CAN CAUSE DAMAGE TO THE FACE OF THE

 BEARING OR THE SEAL.
 (b)  
Examine the spanner nut for burrs.

 (c)  
Remove the burrs from the spanner nut before you install the nut.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 70-24-04
 ALL  ú ú N01 Page 203 ú Oct 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
ELECTRICAL HARNESSES - MAINTENANCE PRACTICES
____________________________________________
 1.  General
_______
 A.  This task gives the steps to install some lockstitch on the electrical harnesses. It also gives the procedure to tighten the electrical connectors.
 TASK 70-24-05-402-001-N00
 2.  Lockstitch Installation (Fig. 201)
_______________________

Lockstitch Installation
Figure 201

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 70-24-05
 ALL  ú ú N01 Page 201 ú Jun 10/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A. Consumable Materials
 (1)  
G00000 Lockstitch

 B.
Access

 (1)  
Location Zones
 410 Engine 1
 420 Engine 2
 430 Engine 3
 440 Engine 4

 C.
Procedure

 S 422-005-N00
 (1)  Install the lockstitch on the wire bundle.
 (a)  
Attach the lockstitch on the wire bundle at distances not more than 2.0 inches (50.8 mm) apart.

 (b)  
Use a clove hitch with an added loop followed by a square knot to make the lockstitch knot.

 NOTE:____The knots must be tight to the wire bundle. The knots must not cause unusual stress or damage.

 (c)  
If the wire bundle diameter is more than 1.5 inches (38.1 mm), attach the lockstitch two times at each location.

 (d)  
Cut the ends of the lockstitch to a length of 0.25-0.50 inches (6.35-12.7 mm).

 TASK 70-24-05-402-017-N00
 3.  Tighten the Electrical Connectors_________________________________
 A. Equipment
 (1)  
Wrench, Strap, TG-70

 (2)  
Pliers, Soft Jawed, TG-69

 B.
Consumable Materials

 (1)  
Solvent, Dielectric (PMC 8910) (P11-054)

 (2)  
Solvent, Cleaner ((PMC 8914) (P11-055)

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 70-24-05
 ALL  ú ú N01 Page 202 ú Jun 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(3)  
Solvent, Cleaner (SPMC 156) (P11-056)

 (4)  
Solvent, Cleaner (SPMC 168) (P11-057)

 (5)  
Solvent, Cleaner (SPMC 175) (P11-058)

 (6)  
Solvent, Cleaner (SPMC 176) (P11-059)

 (7)  
Solvent, Cleaner (SPMC 179) (P11-060)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 STANDARD PRACTICES - ENGINE(39)