L-90039
Jamnut Torque (Oil Lubricated) - Metric Figure 211
K30319
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
70-23-00
ALL ú ú N01 Page 215 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
S 912-052-N00
(3) Electrical connectors of the cigarette type.
(a)
You must tighten all electrical connectors of the cigarrette-type (found at the end of intermediate and high tension leads) until the connector flange touches.
(b)
Approximately 140-160 pound-inches (15.818-18.078 Newton meters) of torque is necessary.
S 912-019-N00
(4)
Use the torque values in Figure 213 for the nuts on a thermocouple probe terminal and the screws on a thermocouple-harness-to-lead.
S 912-020-N00
(5)
Use the torque values in Figure 214 for the nuts on a harness terminal and bus bar in a temperature junction box.
L.
Torque-Check for the Reuse of the Self-Locking Fasteners (Fig. 215, 216)
S 912-053-N00
(1) Do a torque check of self-locking fasteners before reuse.
(a)
Discard the fastener if the lock operation is damaged.
(b)
Do not repair the fastener.
THREAD PITCH TURN ANGLE, TOLERANCE |5`
ALUMINUM ASBESTOS COPPER ASBESTOS NICKEL ASBESTOS STEEL ASBESTOS
8 THREADS PER INCH 135` 67`
9 THREADS PER INCH 135` 67`
10 THREADS PER INCH 135` 67`
11 THREADS PER INCH 180` 90`
12 THREADS PER INCH 180` 90`
13 THREADS PER INCH 180` 90`
14 THREADS PER INCH 180` 90`
16 THREADS PER INCH 270` 135`
18 THREADS PER INCH 270` 135`
20 THREADS PER INCH 270` 135`
24 THREADS PER INCH 360` 180`
28 THREADS PER INCH 360` 180`
ASBESTOS, AND STEEL-ASBESTOS GASKETS. THESE VALUES GIVE A COMPRESSION OF APPROXIMATELY 40% FOR THE ALUMINUM-ASBESTOS AND 20% FOR THE COPPER-ASBESTOS, NICKEL-
L-61912
Installation of Asbestos-Filled Crush-Gasket Figure 212
K30320
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
70-23-00
ALL ú
ú N01 Page 216
ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
THREAD SIZE (POUND-INCHES) TORQUE TORQUE (NEWTON-METERS)
0.138-32 8-10 0.9-1.1
0.164-32 8-12 0.9-1.4
0.190-32 10-15 1.1-1.7
0.216-32 30-35 3.4-4.0
0.250-32 35-40 4.0-4.5
Torque Requirements for Thermocouple
L-90027
L-90028
Probe Terminal Nuts and Screws
Figure 213
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
70-23-00
ALL ú
ú N01 Page 217
ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
E47351
THREAD SIZE (POUND-INCHES) TORQUE TORQUE (NEWTON-METERS)
0.164-32 20-25 2.3-2.8
0.190-32 25-30 2.8-3.4
L-90030 L-90031
Torque Requirements for Harness Terminal
and Bus Bar Attaching Nuts
Figure 214
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
70-23-00
ALL ú ú N01 Page 218 ú Jun 18/99
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 STANDARD PRACTICES - ENGINE(34)
