曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

_______
 A.  This procedure contains three tasks. The first task removes the APU isolation valve. The second task installs the APU isolation valve. The third task does a visual check of the valve and the electrical connections.
 B.  The APU isolation valve is installed in the wheel well for the left body gear. It is in the upper outboard aft corner. You must open the body gear door to get access to the valve.
 C.  It is necessary to install the ground locks for the landing gear before you remove the APU isolation valve.
 TASK 36-11-09-004-001
 2.  Remove the APU Isolation Valve (Fig. 401)
______________________________
 A.  References
 (1)  
AMM 09-11-00/201, Towing and Taxiing

 (2)  
AMM 24-22-00/201, Manual Control

 (3)  
AMM 32-00-30/201, Landing Gear Door Locks

 (4)  
AMM 36-00-00/201, Pneumatic System

 (5)  
IPC 36-11-60 Fig. 1

 B.  
Access

 (1)  
Location Zone
 137A Body Landing Gear Wheel Well, LH

 C.  
Prepare to Remove the Valve

 S 864-002
 (1)  Supply electrical power (AMM 24-22-00/201).
 S 494-003
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO INSTALL
_______ THE DOOR LOCKS ON THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT.
 (2)  
Do this task: "Installation of the Door Locks on the Wing Landing Gear" (AMM 32-00-30/201).

 S 494-043

 (3)  
Do this task: "Installation of the Door Locks on the Body Landing Gear" (AMM 32-00-30/201).

 S 494-004
 WARNING: YOU MUST CAREFULLY INSTALL THE GROUND LOCKS IN ALL LANDING
_______ GEAR. AN ACCIDENTAL RETRACTION OF THE LANDING GEAR CAN CAUSE INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT.
 (4) Install the ground locks in all landing gear (AMM 09-11-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 36-11-09
 ALL  ú ú 01 Page 401 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

SEE A
2. COUPLING (2 PLACES)
SEE B
APU ISOLATION
1. VALVE, V121
FWD  DRIVE MANUAL OVERRIDE 
JUMPER 4. BONDING  SEE  C  CONNECTOR 3. ELECTRICAL  A 
APU Isolation Valve Installation Figure 401 (Sheet 1) 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 36-11-09
 ALL  ú ú 01 Page 402 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

2. COUPLING (2 PLACES)

APU Isolation Valve Installation
Figure 401 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 36-11-09
 ALL  ú ú 01 Page 403 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 S 864-005
 (5)  
Open this circuit breaker on the main power distribution panel, P6, and attach a DO-NOT-CLOSE tag:

 (a)  
6H22 APU ISO VLV AIR SUPPLY PWR

 D. Procedure
 S 984-006
 (1)  
If it is necessary, turn the manual override drive on the valve (1) to put the valve in the OPEN position.

 S 864-007

 (2)  
Put a minimum of one of the wing ISLN switches on the overhead panel, P5, to the OPEN position.

 S 864-008

 (3)  
Release the pressure in the pneumatic system (AMM 36-00-00/201).

 S 034-009

 (4)  
Disconnect the electrical connector DV121 (3) from the APU isolation valve (1).

 S 034-010

 (5)  
Remove the nut (6), washer (7) and bolt (8).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 氣動系統 PNEUMATIC SYSTEM(105)