(2)
AMM 24-22-00/201, Manual Control
(3)
AMM 29-11-00/201, Main Hydraulic Supply System
(4)
AMM 32-00-30/201, Landing Gear Doors
(5)
AMM 36-00-00/201, Pneumatic System
(6)
AIPC 29-11-22, Fig. 2 (Outboard)
(7)
AIPC 29-11-22, Fig. 4 (Inboard)
B.
Access
(1)
Location Zone 546 System 1-Outboard Main Tank, Mid Spar to Rear Spar 544 System 2-Inboard Main Tank, Mid Spar to Rear Spar 644 System 3-Inboard Main Tank, Mid Spar to Rear Spar 646 System 4-Outboard Main Tank, Mid Spar to Rear Spar
(2)
Access Panel
573CB Hydraulic Access Panel-System 1
673CB Hydraulic Access Panel-System 4
C.
Prepare for the Hydraulic System Heat Exchanger Leakage Check
S 496-002
WARNING: YOU MUST CAREFULLY DO THE FOLLOWING STEPS IN THE TASK BELOW TO
_______ INSTALL THE DOOR LOCKS ON THE LANDING GEAR DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(1)
Make sure that the locks for the landing gear doors are installed (AMM 32-00-30/201)
(2)
Remove the pressure from the pneumatic system (AMM 36-00-00/201).
(3)
Remove the pressure from the hydraulic system (AMM 29-11-00/201).
S 866-003
S 866-004
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
29-11-22
ALL ú ú 01 Page 601 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
SEE A SEE B
INBOARD HEAT EXCHANGER INLET AND OUTLET FITTINGS
REAR SPAR
A
REAR SPAR
OUTBOARD HEAT EXCHANGER INLET AND OUTLET FITTINGS
B
Heat Exchanger Hydraulic Connections Figure 601
F84079
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
29-11-22
ALL ú ú 01 Page 602 ú Jun 10/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 016-005
(4)
Get access to the tube connections for the heat exchanger:
(a)
For system No. 1, open the hydraulic access panel 573CB (AMM 06-09-08/201).
(b)
For system No. 2, the tube connections are in the wheel well for the left wing landing gear.
(c)
For system No. 3, the tube connections are in the wheel well for the right wing landing gear.
(d)
For system No. 4, open the hydraulic access panel 673CB (AMM 06-09-08/201).
S 026-006
(5)
Disconnect the hydraulic tubes for the heat exchanger at the rear spar.
S 686-007
(6)
Drain the hydraulic fluid from the hydraulic tubes of the applicable heat exchanger (AMM 29-11-00/201).
S 786-008
(7)
Check the line for blockage with a low pressure dry air or nitrogen source.
(a)
Install an air pressure indicator at the outlet port.
(b)
Apply a dry air pressure source through a shutoff valve at the inlet port.
S 216-022
(8)
Pressurize the heat exchanger to 100 PSI.
S 216-012
(9)
Monitor the pressure gage to determine if a leak is present.
(a)
If the pressure gage shows a decrease in pressure, this indicates that there is leakage in the applicable heat exchanger tubing.
S 866-011
(10)
If you find leakage, replace the applicable heat exchanger
(AMM 29-11-22/401).
D.
Put the Airplane Back to its Usual Condition.
(1)
Remove the air pressure indicators.
S 086-013
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 液壓 HYDRAULIC 2(40)
