29-11-15
 ALL  ú ú 01 Page 217 ú Feb 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 142-081
 (3)  
Clean the bleed hole of the water separator:

 (a)  
Put a wire into the bleed hole.
 NOTE: The wire does not have to go very far into the

____
 housing.

 (b)  
Move the wire to make it touch all the sides of the hole.

 (c)  
Remove the wire.

 S 412-082 CAUTION: MAKE SURE YOU LATCH THE FAIRING DOORS ON THE TRAILING EDGE
_______ CORRECTLY. DAMAGE CAN OCCUR IF THE DOORS OPEN DURING A FLIGHT.
 (4)  Close the fairing doors on the trailing edge of the applicable strut (AMM 54-62-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 29-11-15
 ALL  ú ú 01 Page 218 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 ACCELERATION CONTROL UNIT - REMOVAL/INSTALLATION
________________________________________________
 1.  General_______
 A.  This procedure contains the tasks to remove and install the acceleration control unit. The installation task also contains a test of the control unit installation.
 B.  The acceleration control unit is in the aft nacelle strut. The control unit is attached to the forward side of the turbine drive on the air-driven pump (ADP). Before you remove the control unit, you must remove the ADP turbine drive.
 C.  You can get access to the acceleration control unit through the fairing doors on the trailing edge of the strut.
 TASK 29-11-16-004-001
 2.  Acceleration Control Unit Removal (Fig. 401)_________________________________
 A.  References
 (1)  
AMM 29-11-08/401, Air-Driven Pump Turbine Drive

 (2)  
AMM 54-62-00/201, Nacelle Strut Access Panels

 (3)  
IPC 29-11-41 Fig. 1

 B.  
Access

 (1)  
Location Zone
 454 System 1 - Strut Aft Fairing
 484 System 4 - Strut Aft Fairing

 (2)  
Access Panel
 454A Trailing Edge Fairing Doors - System 1
 484A Trailing Edge Fairing Doors - System 4

 C.  
Procedure

 S 014-002
 (1)  
Open the fairing doors on the trailing edge of the strut (AMM 54-62-00/201).

 (2)  
Remove the ADP turbine drive (AMM 29-11-08/401).

 S 014-003
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 29-11-16
 ALL  ú ú 01 Page 401 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

SEE  A 
SEE B TURBINE DRIVE FOR THE AIR DRIVEN PUMP NUT BOLT WASHER BUSHING (3 LOCATIONS) 
THE CONTROL AIR PRESSURE TUBE FOR 
A  REDUCER ACCELERATION CONTROL UNIT MOUNTING BRACKET PACKING 

VIEW IN THE AFT DIRECTION B
Acceleration Control Unit Installation Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 29-11-16
 ALL  ú ú 01 Page 402 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 024-023
 (3)  
Remove the acceleration control unit:

 (a)  
Disconnect the pressure tube for the control air from the acceleration control unit.

 (b)  
Install a cap on the tube to prevent contamination.

 (c)  
Remove the three nuts, the bolts, the washers, and the bushings from the acceleration control unit.

 (d)  
Remove the acceleration control unit from the mounting bracket on the turbine drive.

 S 034-026
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 液壓 HYDRAULIC 2(11)