(c)  
The installation of the main gear wing door

 (d)  
The installation of one main landing gear

 (e)  
The retraction of the trailing edge flaps

 (3)  
The landing gear support beam will be referred to as the support beam.

 TASK 57-15-00-004-001-B00
 2.  Landing Gear Support Beam Removal_________________________________
 A.  References
 (1)  
AMM 27-51-32/401, Inboard Flap Track Fairings

 (2)  
AMM 27-51-64/401, Flap Torque Tubes

 (3)  
AMM 27-51-69/401, Flap Angle Gearbox

 (4)  
AMM 27-51-71/401, Flap Transmission

 (5)  
AMM 27-62-71/401, No. 4 and 5 Ground Spoiler Actuator

 (6)  
AMM 28-23-00/201, Defueling

 (7)  
AMM 32-11-00/401, Main Landing Gear

 (8)  
AMM 32-13-21/401, Main Gear Wing Door

 B.  Access
 (1)  Location Zone
 310 Left Main Landing Gear
 410 Right Main Landing Gear

 C.  Prepare to Remove the Support Beam
 S 864-002-B00
 (1)  
Defuel the wing fuel tanks (Ref 28-23-00/201).

 (2)  
Lower the trailing edge flaps.

 (3)
Remove the applicable main landing gear (Ref 32-11-00/401).

 (4)  
Remove the wing door (Ref 32-13-21/401).

 S 864-003-B00
 S 034-004-B00
 S 014-005-B00
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 57-15-00
 ALL  ú ú B01 Page 401 ú Nov 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 014-006-B00
 (5)
Remove the fairing for the inboard flap track (AMM 27-51-32/401).

 S 014-007-B00

 (6)  
Open the ground spoilers if more access is necessary.

 D. Remove the Support Beam (Fig. 401)
 S 034-008-B00
 (1)  Remove the stabilizer beam.
 (a)  737-300 AND 737-500; Remove the eyebolt which connects the stabilizer beam to the attach fitting on the support beam.
 NOTE: Do not interchange the forward and aft bolts of the
____ stabilizer beam. Interchange of the bolts can cause a misfair of the wing door.
 (b)  
Move the stabilizer beam down.

 (c)  
Remove the fasteners from the fitting assembly of the stabilizer beam.

 (d)  
Remove the fitting assembly from the support beam.

 (e)  
Make a note of the location of the shims.

 S 034-009-B00
 (2)  Remove the walking beam.
 (a)  
Remove the bolts which attach the fitting assembly on the hanger walking beam to the support beam.

 (b)  
Remove the support fitting.

 (c)  
Make a note of the location of the shims.

 (d)  
Remove the section of the lower wing skin which is attached to the beam.

 (e)  
Disconnect the spoiler braces.

 (f)  
Remove the skin section.

 S 034-010-B00
 (3)  
Remove the two ground spoiler actuators from the aft side of the support beam (Ref 27-62-71/401).

 (4)
Disconnect the necessary hydraulic tubes from the support beam.

 (5)  
Make a note of the locations of the tubes.

 (6)
Disconnect the necessary electrical wires from the support beam.

 (7)  
Make a note of the location of the wires.

 S 034-011-B00
 S 974-033-B00
 S 034-012-B00
 S 974-034-B00
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 57-15-00
 ALL  ú ú B02 Page 402 ú Mar 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (8)  S 034-013-B00Remove the flap transmission (AMM 27-51-71/401).
 (9)  S 034-014-B00Remove the flap angle gear box from the aft side of the support beam (AMM 27-51-69/401).
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 機翼 WINGS(7)