57-21-11
ALL ú ú B02 Page 804 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(j) Sand the bonded plastic surface with finer grits of moist or dry abrasive papers to get the necessary finish.
NOTE:____ The abrasive papers that you can use are (280, 320, 400 and 600).
(k) Wind the abrasive papers around a rubber blocks that have durometer indication of 35 |5, the shore A scale.
NOTE:____ You also can wind the abrasive papers around the block that have a cotton-flannel.
(l) Cover the surface with water while you sand the surface.
NOTE:____ Be careful not to cause too much heat while you sand the area.
(m) Hold the area that you sanded to a minimum necessary area until you get a satisfactory repair.
NOTE:____ It is necessary to make the area that is adjacent to the smooth repaired area look smooth.
(n) (o) (p) (q) (r) During each step, you must remove the remaining scratches when you continue to grade the adhesive.Clean with water each time you change the grit.Get a smooth surface.Clean with water until you remove the grit.Follow these steps to polish and to get a good visual finish: 1) Polish the surface with the machine.
NOTE:____ Polish with the machine is better when the equipment and an approved person are available.
2) 3) 4) 5) 6) Touch with pressure.Balance the feed rate and the wheel speed to prevent too much heat.Use a stitched muslin wheel and learock S-30 buffing compound for the initial buffing.Change the direction of the feed constantly and use only light pressure.Complete the polish with a loose, open, not stitched wheel with spares and Learock 888 buffing compound for brighter results.
NOTE:____ You can make the spacers when you remove all the muslin discs. Use the scissors to decrease half of them to the half initial diameter.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
57-21-11
ALL ú ú B02 Page 805 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
7) Assemble the wheel. a) 1. Do the large discs first and then do the small discs.
NOTE: This wheel will decrease the surface heat
____ because of the friction.
8) Do these steps to polish the area by hand.
NOTE: You can polish the area by hand when the polishing
____ machine and an approved person are not available.
a) Polish the area where it is necessary until you get good finish.
NOTE: Use 0000 wet rough which is applied to a wet
____
cotton-flannel pad.
b) Apply a polish to a clean, wet cotton-flannel pad. c) Polish where it is necessary until you get good finish. d) Rub with a clean cotton-flannel cloth.
(s)
Apply a thin, smooth film of the wax with a clean cotton-flannel pad.
(t)
Rub lightly with a circular movement until the area is glossy.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
57-21-11
ALL ú ú B02 Page 806 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
WING TIP LENS
WING TIP LENS
(EXAMPLE)
Wing Tip Lens Repair
Figure 801
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
57-21-11
ALL ú ú B01 Page 807 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
K32791
1.
2.
3.
A
737-300/400/500MAINTENANCE MANUAL
PLATES/SKIN - DESCRIPTION AND OPERATION
_______________________________________
General
_______
A. The exterior surface of the wing comprises the wing skin and the flight control surfaces attached to the wing. This section describes the wing skin, which can be divided into skin of primary and secondary structural importance.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 機翼 WINGS(18)
