(a)
Apply sealant to all surfaces and countersinks below the fastener head.
(b)
Install the fastener.
S 102-088-B00
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
51-31-00
ALL ú ú B01 Page 213 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
FAIRING SEAL AT METAL SEAL COVER
FILLET AFTER INSTALLATION
YOU CAN APPLY THE SEALANT TO THE HOLE OR THE FASTENER
Fastener Seal
Figure 204 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
51-31-00
ALL ú ú B02 Page 214 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
METAL EXTRUDED SEAL COVER
SEALING OF
STANDARD GROUND STUD
Fastener Seal
Figure 204 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
51-31-00
ALL ú ú B02 Page 215 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
M27629
A
737-300/400/500
MAINTENANCE MANUAL
PROTRUDING HEAD FASTENER COUNTERSUNK FASTENER
PROCEDURE 2
TYPICAL FASTENER SEALING FOR CORROSION PROTECTION
Fastener Seal
Figure 204 (Sheet 3)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
51-31-00
ALL ú ú B01 Page 216 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
M27705
A
737-300/400/500MAINTENANCE MANUAL
CLASS A (BRUSHABLE) IF USED,
D
MAY COVER THE FASTENER HEAD
D B D
B
D D DBD
W
W
W
RIVET HEAD
BOLT LESS THAN
AND BUTTON
1/2-INCH DIA
D BOLT 1/2-INCH
B
OR LARGER DIA
A
B
C
B
D B D W
W
HEX DRIVE (HI-LOCK)/BOLT/LOCKBOLT HEX DRIVE (HI-LOCK) COLLAR
LESS THAN 3/8-INCH DIA 1/2-INCH AND LARGER DIA BOLT 2
D
E
B
D
B
B
D B
B
W
D
W W
HEX DRIVE (HI-LOCK)/ BOLT/LOCKBOLT LOCK BOLT HEX DRIVE (HI-LOCK) COLLAR 3/8-INCH OR LARGER DIA COLLAR LESS THAN 1/2-INCH DIA BOLT 2
F GH
2 RECESSED AREA IN END OF HEX DRIVE PIN NEED NOT BE FILLED WITH SEALANT D = 0.02 INCH (0.508 mm) MINIMUM B = 0.10 INCH (2.54 mm) MINIMUM, EXCEPT 0.20 INCH (5.08 mm) MAXIMUM
FOR VIEWS C, D, AND F.
W = 0.10 INCH (2.54 mm) MINIMUM TO 0.20 INCH (5.08 mm) MAXIMUM
TYPICAL FILLET SEALING DIMENSIONS FOR CORROSION PROTECTION
Fastener Seal
Figure 204 (Sheet 4)
M27706
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
51-31-00
ALL ú ú B01 Page 217 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(c)
A continous extrusion of sealant is necessary around the fastener.
(d)
Clean off unwanted sealant.
S 392-090-B00
(3) Procedure 2 - corrosion protection below the head area and shank of the fastner:
(a) Apply selant to the entire shank and thread of the fastener.
NOTE: Apply sealant to the shank only for fasteners which will
____
use self-sealing nuts or collars.
(b)
Install the fastener and nut or collar.
(c)
Clean off unwanted sealant.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 結構 STRUCTURES(66)
