500
Feb 20/91 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 34-42-21 Page 301
GPWS CONTROL MODULE - REMOVAL/INSTALLATION
1. General
A. This subject has two tasks. One is for the removal and one is for the installation of the GPWS control module. These tasks have steps for the removal of the control module, the installation of the replacement control module, and a test of the control module panel lights.
B. The GPWS control module is installed on the first officer's instrument panel, P3.
2. GPWS Control Module Removal
A. Procedure
(1)
Open these circuit breakers and attach DO-NOT-CLOSE tags:
(a)
P6 Main Power Distribution Panel
1) DIM & TEST INDICATOR LIGHTS
(b)
P18 Overhead Circuit Breaker Panel
1) GND PROX WARN
(2)
Remove the GPWS control module.
(a)
Loosen the fasteners on the control module.
(b)
Pull the control module out from the instrument panel until you can get to the electrical connector.
(c)
Disconnect the electrical connector from the control module.
3. GPWS Control Module Installation
A. References
(1) 24-22-0, Manual Control (Apply Power)
B. Procedure
(1)
Open these circuit breakers and attach DO-NOT-CLOSE tags:
(a)
P6 Main Power Distribution Panel
1) DIM & TEST INDICATOR LIGHTS
(b)
P18 Overhead Circuit Breaker Panel
1) GND PROX WARN
(2)
Install the GPWS control module:
(a)
Connect the electrical connector to the control module.
(b)
Lightly push the control module into the instrument panel.
(c)
Tighten the fasteners that attach the control module to the instrument panel.
(3)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:
(a)
P6 Main Power Distribution Panel
1) DIM & TEST INDICATOR LIGHTS
(b)
P18 Overhead Circuit Breaker Panel
1) GND PROX WARN
(4)
Supply electrical power (Ref 24-22-0).
(5)
Make sure the GPWS control module panel lights are on.
(6)
Remove electrical power if it is not necessary (Ref 24-22-0).
500
Feb 20/91 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 34-42-21 Page 401
LOW RANGE RADIO ALTIMETER SYSTEM - DESCRIPTION AND OPERATION
EFFECTIVITY
GJ ALL EXCEPT B-2509, B-2510
1. General
A. The low range radio altimeter (LRRA) system supplies vertical position information for use by the pilots during approach and landing phases of flight operation. The LRRA system provides an accurate measurement of absolute altitude (height above terrain) from 2500 feet to touchdown. Flag alarm, A/P failure warning, dc altitude, and vertical terrain clearance (altitude trip) outputs are available for use by other systems.
B. The system consists of a receiver-transmitter, two height indicators, two decision height (DH) lights (one on each ADI), transmit antenna, and receive antenna. The location of components is shown on Fig. 1.
C. The system receives 115-volt ac power through circuit breaker RADIO ALTM-1 located on panel P18-1 at the left load control center.
D. The LRRA system supplies flag alarm and dc altitude signals to the autopilot system and flag alarm and 200- and 1500-foot altitude trip signals to the flight director system. Dc altitude and flag alarm signals are supplied to the ground proximity warning system.
2. Receiver-Transmitter (Fig. 1)
A. The receiver-transmitter is located on shelf four of E2 electronic rack. All electrical connections to the receiver-transmitter are made through a connector located on the rear panel. An auxiliary connector located on the front panel is provided for connecting to test equipment.
3. Height Indicator (Fig. 1)
A. Airplane altitude is read from a circular dial which is calibrated from 0 to 2500 feet. Dial calibration is linear from -10 to 480 feet and logarithmic from 480 to 2500 feet. Below 500 feet, the dial is divided into 10-foot increments. Above 500 feet, it is divided into 100-foot increments.
B. The DH control knob is used to adjust the position of the DH cursor to any altitude shown on the dial. The DH cursor setting designates the altitude at which the DH light on each ADI will be energized during airplane descent or de-energized during airplane ascent.
C. The warning flag is solenoid operated and will come into view whenever the solenoid is de-energized.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機維護手冊 導航 NAVIGATION 2(59)
