1) Position flight director mode selector to OFF.
Check ADI for following: 
ATT flag - Out of view
CMPTR flag - Out of view
V-Bars - Out of view
SPEED flag - In view
GS flag - In view
RUNWAY flag - In view
Runway symbol - In view behind Runway flag
Attitude Sphere - Displays airplane attitude.

2) Open appropriate VG circuit breaker. Check ATT flag comes into view. 3) Close VG circuit breaker. Check ATT flag goes out of view. 4) Open appropriate FLT DIR AC and DC circuit breakers. Check CMPTR flag
comes into view. 5) Close FLT DIR AC and DC circuit breakers. Check CMPTR flag goes out of view.
6)  On flight director control panel, position mode selector to MAN GS and then to AUTO APP. Check CMPTR, RUNWAY and GS flags are in view, V-Bars are out of view, and check F/D Approach Progress Display for green VOR/LOC annunciation.
7)  On appropriate VHF NAV control panel, actuate UP/LT self-test while checking for following: a) After 3 seconds CMPTR, RUNWAY, and GS flags go out of view, V-Bars
come into view and display up left steering command, glide slope pointer deflects up, and runway symbol moves left. b) After 20 seconds CMPTR, RUNWAY, and GS flags come into view, V-Bars
go out of view, and runway symbol returns to center. 8) Release Up/LT test switch. 9) Close appropriate LRRA system circuit breakers. Check ADI runway symbol
moves up to bottom of airplane symbol. 10) Tune appropriate VHF NAV receiver to a VOR frequency. Check ADI RUNWAY
flag, symbol, GS flag and glide slope pointer go out of view.
11) Position flight director mode selector to OFF.
12) Remove external electrical power if no longer required.

5C8 
34-26-11 Page 402  BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  Jun 20/85 

3.  ADI Removal/Installation (Airplanes with Sperry SP177 Auto Flight Control System)
A.  Remove Indicator
(1)  
Open following listed circuit breakers on P18 or P6 circuit breaker panel (system 1 for CAPT ADI, system 2 for F/0 ADI):  ADI ADI ALT Autothrottle (A/T)  FLT DIR  VHF NAV (VOR/LOC, G/S) VERT GYRO

(2)  
Loosen clamp and pull out indicator.

(3) 
 Disconnect electrical connectors.

B.  Install Indicator
(1)  
Connect electrical connectors, push in indicator, and tighten clamp.

(2)  
Close circuit breakers opened in step A.(1).

C.  Test Indicator
(1)  
The following tests are provided to check attitude director indicator operation. For a quick check of indicator after installation perform Indicator Self-Test in paragraph (2). For a more complete check of the indicator perform the Indicator Self-Test in paragraph (2) and the Indicator Command Bar and Warning Flag Test in paragraph (3).

(2)  
Indicator Self-Test

(a)  
On appropriate ADI, press and hold TEST switch. Check ATT flag appears and horizon sphere rotates left 15 to 25 degrees and down 5 to 15 degrees.

(b)  
Release TEST switch. Check horizon sphere returns to display airplane attitude and ATT flag retracts from view.

(c)  
If no further tests are required, remove electrical power.

(3)  
Indicator Command Bar and Warning Flag Test

(a)  Prepare to test. 1) Provide electrical power. 2) Check all circuit breakers for air data, attitude reference, autopilot, autothrottle,
compass, low range radio altimeter, performance data computer, VOR/ILS navigation and flight instrument systems are closed and all systems are operational.
3)  Tune VHF NAV receivers to a localizer frequency other than local VOR/TAC station. Check ADI LOC and GS flags and glide slope pointer come into view.
(b)  Test
1)  On AFCS mode control panel, position flight director switch to OFF. Check ADI for following: ATT flag - Out of view FD flag - Out of view Command Bars - Out of view SPD flag - In view GS flag - In view Glide slope pointer - In view LOC flag - In view Localizer pointer - Out of view Attitude Sphere - Displays airplane attitude. 
5C8 
Jun 20/85  BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  34-26-11 Page 403 

2)  Open appropriate VG circuit breaker. Check ATT flag comes into view.
3)  Close VG circuit breaker. Check ATT flag goes out of view.
4)  Open appropriate FLT DIR AC and DC circuit breakers. Check FD flag comes into view.
5)  Close FLT DIR AC and DC circuit breakers. Check FD flag goes out of view.
6) On appropriate VHF NAV control panel, actuate UP/LT self-test while checking for following: a) After 3 seconds FD, LOC, and GS flags go out of view, glide slope pointer deflects up, and localizer pointer deflects left. b) After 20 seconds FD, LOC, and GS flags come into view, and localizer pointer returns to center.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機維護手冊 導航 NAVIGATION 2(2)