(2)  
Nonmagnetic tools to adjust the standby magnetic compass

(3)  
One Compass Correction Card - AN5823-1

(4)  
Standby Compass Calibrator Kit, Honeywell - 2591553-901

(5) 
 Nonmagnetic tripod

B.  References
(1)  
AMM 9-10-00/201, Towing

(2)  
AMM 24-22-00/201, Manual Control (Apply Power)

C.  Calibrator Adjustment (Fig. 201)
(1)  Do this procedure to calibrate the standby compass calibrator (SCC) to the magnetic field at the location of the compass swing area:
(a)  
Make sure that there are no vehicles or airplanes less than 250 feet away.

(b)  
Make sure that there are no buildings less than 250 feet away.

(c)  
Put a nonmagnetic tripod at the center of the compass swing area.

(d)  
Attach a master magnetic compass to the SCC with two mounting screws.

NOTE:  You can use an accurate standby magnetic compass for a master magnetic compass. Make sure that the N-S and E-W adjustment screws are at neutral.

(e)  
Put the SCC/master compass assembly on the tripod.

NOTE:  Make sure the assembly is level.

(f)  
Turn the assembly until the master magnetic compass displays an indication of magnetic north (N).

(g)  
Turn the top and bottom SCC dials to show an indication of E at the index line.

501 
May 01/99  BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  34-24-11 Page 201 

F17935
Standby Compass Calibrator  500 
34-24-11  Figure 201  Aug 01/95 
Page 202 
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 

(h)  
Make a record of the heading shown on the standby magnetic compass.

(i)  
Turn the top and bottom SCC dials to show and indication of W at the index line.

(j)  
Make a record of the heading shown on the standby magnetic compass.

(k)  
Turn the magnetic field cancellation adjustment screw on the SCC to decrease the heading errors in each direction (E and W) to a minimum.

(l)  
Continue to adjust the SCC dials for each direction (E and W). Then use the field cancellation adjustment screw until the errors are at a minimum.

NOTE:  Continue to do this procedure until the error in each direction is at a minimum. Do not move the field cancellation adjustment screw before the compass swing is completed.
D.  Prepare for a Compass Swing of the Standby Compass
NOTE:  Ferromagnetic parts installed near the standby compass can cause compass heading errors. Make sure no ferromagnetic parts are near the captain's and the first officer's window frames. If found, replace the parts with nonmagnetic, corrosion-resistant steel (CRES) parts.
(1)  Tow the airplane to the compass swing area (AMM 9-10-00/201).
NOTE:  The compass swing area must be a level area with a smooth surface. It must be sufficiently strong to hold the weight of the airplane. The area must be large enough to tow or taxi the airplane. Make sure all vehicles other than the tow vehicle are not less than 250 feet from the airplane.
The horizontal component of the earth's-magnetic field must be constant (+ 1 degree) in the test area. Measure the horizontal. component if magnetic material (such as a new building) is less than 600 feet from the compass swing area. Do not use the compass swing area if the horizontal component is not constant (+ 1 degree).
(2)  
Supply the electrical power (AMM 24-22-00/201).

(3)  
Energize all of the electronic equipment, radios, and control cabin lighting for the usual conditions that occur in flight.

(4)  
Make sure that the N-S and E-W adjustment screws on the standby compass are at neutral.

CAUTION:  USE TOOLS THAT ARE NOT MAGNETIC. MAGNETIC TOOLS CAN CAUSE COMPASS DIFFERENCES.

(5)
Make sure all vehicles but the tow truck are not less than 250 feet from the airplane.

500 
Aug 01/95  BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  34-24-11 Page 203 

E.  Standby Compass Adjustment
NOTE:  The steps that follow are for the four-point calibration swing.
(1)  
Turn the airplane to a magnetic heading of 0 degrees.

(2)  
Remove and keep the lower left and upper right mounting screws on the standby magnetic compass.

(3)  
Use the two mounting screws to install the SCC on the face of the standby magnetic compass.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機維護手冊 導航 NAVIGATION 1(85)