- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) (Ref. AMM TASK 73-21-60-400-001).
 (b) If the resistance values are out of the specified limits:
 - disconnect the harness J10 from the starter shutoff valve and do a check of the starter shutoff valve resistance between: . pins 1 and 2 (15 to 60 Ohms) . pins 1 and 5 (> 10 Megohms) . pins 1 and ground (> 10 Megohms).
 1 If the resistance values are in the specified limits:
_

 - replace the harness J10 (Ref. AMM TASK 73-21-50-000-043) (Ref. AMM TASK 73-21-50-400-043).
 2 If the resistance values are out of the specified limits:
_

 - replace the starter shutoff valve (Ref. AMM TASK 80-11-20-000-003) (Ref. AMM TASK 80-11-20-400-003).
 B. Do the test given in Para. 3.A.
 F 『 EEFF : ALL E ∞∞80-11-00∞∞∞∞∞∞∞∞∞∞Page 220
 E E May 01/99 ERE
ECES E

 F 『
 E C F M E
 E E
 E 56 E
 E E

 TASK 80-11-00-810-809

 Failure of the Control of the Starter Shutoff Valve Solenoids through the two
 Channels on Engine 1
 1. Possible Causes
_______________

 - ECU (4000KS)

 - harness J9

 - harness J10

 - starter shutoff valve

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
AMM 73-21-50-000-042 Removal of the HJ9 Harness
 AMM 73-21-50-000-043 Removal of the HJ10 Harness
 AMM 73-21-50-400-042 Installation of the HJ9 Harness
 AMM 73-21-50-400-043 Installation of the HJ10 Harness

R  AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)(4000KS) AMM 73-21-60-400-001 Installation of the Electronic Control Unit
R (ECU)(4000KS) AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with Engine non Motoring) AMM 80-11-20-000-003 Removal of the Starter Shutoff Valve AMM 80-11-20-400-003 Installation of the Starter Shutoff Valve ASM 74-31/01
 3. Fault Confirmation
__________________

 A. Do the operational test of the FADEC 1A and 1B on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
 4. Fault Isolation
_______________

 A. If the test gives the maintenance messages SAV (SOL), J9, ECU + SAV (SOL), J10, ECU:
 - do a check for open or short to ground of the harnesses J9 and J10 between the ECU (4000KS) and the starter shutoff valve solenoid, pins J9 and J10/11, 12 to pins J9 and J10/1, 2 (Ref. ASM 74-31/01).
 (1) If one of these wirings is not correct:
 - repair the defective above wirings.
 F 『 EEFF : ALL E ∞∞80-11-00∞∞∞∞∞∞∞∞∞∞Page 221
 E E May 01/99 E E ECES
E E 56 E E E (2) If these wirings are correct:

 F  『
 E  C F M  E
 E  E

 - disconnect the harnesses J9 and J10 from the ECU (4000KS) and do a check of the ECU resistance cables between: . pins 11 and 12 (15 to 60 Ohms) . pins 11 and 3 (> 10 Megohms) . pins 11 and ground (> 10 Megohms).
 (a) If the resistance values are in the specified limits:

 - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) (Ref. AMM TASK 73-21-60-400-001).

 (b) If the resistance values are out of the specified limits:

 - disconnect the harnesses J9 and J10 from the starter shutoff valve and do a check of the starter shutoff valve resistance between: . pins 1 and 2 (15 to 60 Ohms) . pins 1 and 5 (> 10 Megohms) . pins 1 and ground (> 10 Megohms).
 1 If the resistance values are in the specified values:
_

 - replace the defective harness J9 (Ref. AMM TASK 73-21-50-000-042) (Ref. AMM TASK 73-21-50-400-042) or harness J10 (Ref. AMM TASK 73-21-50-000-043) (Ref. AMM TASK 73-21-50-400-043).
 2 If the resistance values are out of the specified limits:
_

 - replace the starter shutoff valve (Ref. AMM TASK 80-11-20-000-003) (Ref. AMM TASK 80-11-20-400-003).
 B. Do the test given in Para. 3.A.
 F 『 EEFF : ALL E ∞∞80-11-00∞∞∞∞∞∞∞∞∞∞Page 222
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 STARTING 起動(17)