曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 Actuator Assembly AMM 75-31-70-000-001 Removal of the Variable Bleed Valve Position Sensor AMM 75-31-70-000-002 Removal of the Variable Bleed Valve position Sensor AMM 75-31-70-400-001 Installation of the Variable Bleed Valve Position
 Sensor AMM 75-31-70-400-002 Installation of the Variable Bleed Valve position Sensor
 3. Fault Confirmation
__________________
 A. Do the operational test of the FADEC 1A on the ground (with engine motoring) (Ref. AMM TASK 73-29-00-710-040).
 NOTE : The failure message is generated if the actual position and the
____ demanded position of the VBV system disagree (only the position of VBV Master actuator door is monitored).
 NOTE : There is no expected position of the VBV actuators on a non
____ running engine. The position of the VBV actuators must be uniform but can be either open, closed or in an intermediate position.
 4. Fault Isolation
_______________
 A. If the test does not give the maintenance message "VBV ACT, HMU":
 - do a visual inspection of all the VBV doors actuators and flexible shafts through the fan duct panels, check for offset of position between all VBV doors (all VBV doors not set in the same position) :
 (1) If an offset between VBV doors or damage to VBV flexible shafts is observed:
 (a) Remove all the flexible shafts (Ref. AMM TASK 75-31-30-000-001).
R  (b) Inspect the rod ends of each flexible shaft (Ref. AMM TASK 75-31-
R  30-200-002). Replace any flexible shaft exhibiting excessive wear (Ref. AMM TASK 75-31-30-000-001) and (Ref. AMM TASK 75-31-30-400-001). In case of wear on the flexible shafts ends, all VBV doors shall be inspected and manually operated.
 F 『 EEFF : ALL E ∞∞75-30-00∞∞∞∞∞∞∞∞∞∞Page 202
 E E Feb 01/03 E E ECES
E

 F  『
 E  C F M  E
 E  E
 E  56  E
 E  E

 (c) Operate each of the 11 VBV actuator both directions and make sure that each moves smoothly and freely.
 NOTE : During this check, apply a manual load tending to force
____ the door towards its open position. Replace any suspect VBV ballscrew actuator (Ref. AMM TASK 75-31-60-000-002) and (Ref. AMM TASK 75-31-60-400-002).
 (2) If nothing is found, following Trouble Shooting must be performed at first opportunity within 10 cyles (except if the fault re-occurs):
 - do a check of the rigging of the feedback rod to the VBV position sensor (RVDT) (Ref. AMM TASK 75-31-70-400-002).
 (a) Remove all the flexible shafts (Ref. AMM TASK 75-31-30-000-001).
R  (b) inspect the rod ends of each flexible shaft (Ref. AMM TASK 75-31-
R  30-200-002). Replace any flexible shaft exhibiting excessive wear (Ref. AMM TASK 75-31-30-000-001) and (Ref. AMM TASK 75-31-30-400-001). In case of wear on the flexible shafts ends, all VBV doors must be inspected and manually operated.
 (c) Operate each of the 11 VBV actuators both directions and make sure that each moves smoothly and freely.
 NOTE : During this check, apply a manual load tending to force
____ the door towards its open position. Replace any suspect VBV ballscrew actuator (Ref. AMM TASK 75-31-60-000-002) and (Ref. AMM TASK 75-31-60-400-002).
 (d) Remove the VBV gear motor/stop mechanism assembly (Ref. AMM TASK 75-31-20-000-002).

 (e) Check for free rotation of the VBV gear motor. If it does not move freely

 - replace the VBV gear motor (Ref. AMM TASK 75-31-10-000-002) and (Ref. AMM TASK 75-31-10-400-002).

 (f) Check for free rotation of the stop mechanism. If it does not move freely

 - replace the VBV stop mechanism (Ref. AMM TASK 75-31-20-000-002) and (Ref. AMM TASK 75-31-20-400-002).

 (g) Check for free rotation of the VBV master door actuator. If it does not move freely

 - replace the VBV master door actuator (Ref. AMM TASK 75-31-50-000-002) and (Ref. AMM TASK 75-31-50-400-002).
R  (h) Inspect the rod ends of the main flexible shaft (Ref. AMM TASK
R  75-31-30-200-002). Replace the main flexible shaft in case of excessive wear (Ref. AMM TASK 75-31-30-000-002) and (Ref. AMM TASK 75-31-30-400-002).
 F  『
 ∞∞75-30-00∞∞∞∞∞∞∞∞∞∞Page 203
EEFF :  ALL  E 
E  E  Feb 01/03
 E  E
 ECES  E

 F 『
 E C F M E
 E E
 E 56 E
 E E
 (i) Pre SB 75-007

 1 If no fault is found:
_
 - disconnect the harness from the ECU receptacle and visually examine the receptacle and the connector for damaged pins or contamination (Ref. AMM TASK 73-21-50-210-002).
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 大氣 AIR(50)