(b) If the circuit breaker stays closed:

 - install the ECU (4000KS) (Ref. AMM TASK 73-21-60-400-001).
 1 If the circuit breaker trips:
_
 - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
 2 If the circuit breaker trips again:
_
 - do a check and repair the wiring between the ECU (4000KS) pins J1/7, 8 and the EIU-1 (1KS1) pin AB/14B.
 (4) If the fault continues:
 - make sure that there is no ground signal at the EIU-1 (1KS1) pin AA/5B.
 C. Do the test given in Para. 3.
 F 『 EEFF : ALL E ∞∞71-50-00∞∞∞∞∞∞∞∞∞∞Page 247
 E E Nov 01/02 ERE
ECES E

 F 『
 E C F M E
 E E
 E 56 E
 E E

 TASK 71-50-00-810-825
 Loss of the 115VAC Power Supply on the ECU 2
 1. Possible Causes
_______________
 - EIU-2 (1KS2)

 - ECU (4000KS)

 - J1 harness

 - wiring

 - C/B-ENGINE/1 AND 2/IGN/SYS A (1JH)

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)(4000KS) AMM 73-21-60-400-001 Installation of the Electronic Control Unit R (ECU)(4000KS) AMM 73-25-34-000-040 Removal of the Engine Interface Unit (EIU) (1KS1,1KS2) AMM 73-25-34-400-040 Installation of the Engine Interface Unit (EIU) (1KS1,1KS2) AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with Engine non Motoring) ASM 74-31/01
 3. Fault Confirmation
__________________
 A. Make sure that this(these) circuit breaker(s) is(are) closed:
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU ENGINE/1 AND 2/IGN/SYS A 1JH A03
 B. Test
 (1) If you cannot close the circuit breaker (1JH), refer to Para. 4.B.

 (2) Do the operational test of the FADEC 2B on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).

 F 『 EEFF : ALL E ∞∞71-50-00∞∞∞∞∞∞∞∞∞∞Page 248
 E E Aug 01/99 E E ECES
E

 F 『
 E C F M E
 E E
 E 56 E
 E E

 4. Fault Isolation
_______________
 A. If the circuit breaker (1JH) is closed and if the test gives the maintenance message J1, 115 VAC, ECU:
R  CAUTION : WHEN THE "ENG/MASTER" LEVER IS IN THE "ON" POSITION, BE VERY_______
R  CAREFUL NOT TO SET THE "ENG/MODE" SELECTOR SWITCH TO "CRANK" OR
R  "IGN/START".
R  IF YOU DO SET THE SELECTOR SWITCH TO ONE OF THESE POSITIONS,
R  THE ENGINE WILL START. THERE IS THUS A RISK OF INJURY TO
R  PERSONS AND OF DAMAGE TO EQUIPMENT.
R - On the panel 115 VU, set the MASTER switch to "ON".
 - do a check for 115VAC at the ECU (4000KS) pins J1/7, 8 (Ref. ASM 74-
31/01). R - On the panel 115 VU, set the MASTER switch to "OFF".
 (1) If there is 115VAC:

 - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).

 (2) If there is no 115VAC:

 - do a check for 115VAC at the EIU-2 (1KS2) pin AB/14F.
 (a) If there is 115VAC:
 - replace the EIU-2 (1KS2) (Ref. AMM TASK 73-25-34-000-040) and (Ref. AMM TASK 73-25-34-400-040).
 1 If the fault continues:
_
 - replace the J1 harness between the EIU-2 (1KS2) and the ECU (4000KS).
 (b) If there is no 115VAC:
 - do a check of the wiring between the EIU-2 (1KS2) pin AB/14F and the circuit breaker (1JH).
 1 If there is no continuity:
_ - repair the above wiring.
 2 If there is continuity:
_
 - replace the C/B-ENGINE/1 AND 2/IGN/SYS A (1JH).
 (3) If the fault continues:
 - make sure that there is no ground signal at the EIU-2 (1KS2) pin AA/5B.
 B. If the circuit breaker (1JH) is open:
 - close it.
 (1) If the circuit breaker trips:
 - remove the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and

 - remove the EIU-2 (1KS2) (Ref. AMM TASK 73-25-34-000-040).

 F 『 EEFF : ALL E ∞∞71-50-00∞∞∞∞∞∞∞∞∞∞Page 249
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊(cè) 動(dòng)力裝置 POWER PLANT(24)