(b) If the fault continues:

 - replace the CTL UNIT-THROTTLE, ENG 1 (8KS1) (Ref. AMM TASK 76-11-19-000-042) and (Ref. AMM TASK 76-11-19-400-042).

 (c) If the fault continues:

 - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).

 (d) If the fault continues:

R  - do a check for a short to ground between (Ref. ASM 73-25/16): .the EIU1 (1KS1) pin AA/4C and the TCU1 (8KS1) pin E/C .the EIU1 (1KS1) pin AA/4A and the TCU1 (8KS1) pin E/C .the relay (14KS1) and its related wiring.
 1 If nothing is found:
_
 - replace the thrust reverser harness (Ref. AMM TASK 71-51-43-000-044) and (Ref. AMM TASK 71-51-43-400-044).
 B. Do the test given in Para. 3.
 (1) No additional maintenance action is required if the fault is not confirmed.

 (2) Repeat the fault isolation procedure if the fault continues.

 F 『 EEFF : ALL E ∞∞71-50-00∞∞∞∞∞∞∞∞∞∞Page 215
 E E May 01/00 E E ECES
E TASK 71-50-00-810-806

 F  『
 E  C F M  E
 E  E
 E  56  E
 E  E

 Failure of the Thrust Reverser Inhibition Switch - Engine 2 - Channel A
 1. Possible Causes
_______________
 - CTL UNIT-THROTTLE, ENG 2 (8KS2)

 - EIU-2 (1KS2)

 - RELAY-THRUST REV INHIBITION, ENG 2 (14KS2)

 - thrust reverser harness

 - aircraft wiring

 - ECU (4000KS)

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 71-51-43-000-044 Removal of the Thrust Reverser (Channel A and B) Harness (4200KS) AMM 71-51-43-400-044 Installation of the Thrust Reverser (Channel A and B)
 Harness (4200KS) AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU) AMM 73-21-60-400-001 Installation of the Electronic Control Unit (ECU) AMM 73-25-34-000-040 Removal of the Engine Interface Unit (EIU) AMM 73-25-34-400-040 Installation of the Engine Interface Unit (EIU) AMM 76-11-19-000-042 Removal of the Throttle Control Unit (8KS1, 8KS2) AMM 76-11-19-400-042 Installation of the Throttle Control Unit (8KS1,
 8KS2) AMM 78-31-00-710-042 Operational Test of the Thrust Reverser System ASM 73-25/16 ASM 73-25/16 ASM 78-37/01
 3. Fault Confirmation
__________________
 A. Make sure that the throttle lever is not in the thrust reverser area.
 B. Do the operational test of the thrust reverser system (Ref. AMM TASK 78-31-00-710-042).
 F 『 EEFF : ALL E ∞∞71-50-00∞∞∞∞∞∞∞∞∞∞Page 216
 E E May 01/00 ERE
ECES E

 F 『
 E C F M E
 E E
 E 56 E
 E E

 4. Fault Isolation
_______________
 A. This fault message is generated when the ECU detects an unwanted closure of the inhibition relay 14KS2 or a short or short to ground in the harness J5 or in the thrust reverser harness or in the aircraft wiring.
 CAUTION : MAKE SURE THAT THERE IS NO HYDRAULIC PRESSURE WHILE YOU DO THIS
_______ TEST. PUT A WARNING NOTICE IN THE COCKPIT TO TELL PERSONS NOT TO PRESSURIZE THE HYDRAULIC SYSTEMS.
 (1) If the test gives the maintenance message J5, TR ACFT SW, ECU: - on the overhead panel 50VU, push and release the P/BSW-ENG/FADEC
 GND PWR/2 (7KS2) the ON legend comes on, R
 - remove the RELAY-THRUST REV INHIBITION, ENG 2 (14KS2) from 188VU and do a check for 28VDC at pin A/X on the relay base (Ref. ASM 73-25/16).
 (a) If there is 28VDC: R
 - disconnect the connector E from the TCU2 (8KS2) and do a check for ground at pin E/C.
 1 If there is ground:
_
 - replace the CTL UNIT-THROTTLE, ENG 2 (8KS2) (Ref. AMM TASK 76-11-19-000-042) and (Ref. AMM TASK 76-11-19-400-042).
 2 If there is no ground:
_ - on the overhead panel 50VU, push the P/BSW-ENG/FADEC GND PWR/2 (7KS2) the ON legend goes off,
 - remove the EIU2 (1KS2) (Ref. AMM TASK 73-25-34-000-040) and disconnect the connector E from the TCU2 (8KS2),

 - do a check for a short to ground between (Ref. ASM 78-37/01): .the EIU2 (1KS2) pin AA/4C and the TCU2 (8KS2) pin E/C .the EIU2 (1KS2) pin AA/4A and the TCU2 (8KS2) pin E/C.

 3 If there is a short to ground:
_ - repair as required.
 4 If nothing is found:
_
 - replace the EIU-2 (1KS2) (Ref. AMM TASK 73-25-34-000-040) and (Ref. AMM TASK 73-25-34-400-040).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 動力裝置 POWER PLANT(13)