「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 R EFF : 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
CES 1QT A132QT M27
∞∞28-42-00∞∞∞∞∞∞∞∞∞∞Page A278
Aug 01/05
B. Test
(1) To keep the number of computer replacements (with no fault found) to a minimum, do the power on BITE test of the FQIS as follows:
(a) If the FQIS is not energized:
1 Close the C/Bs 1QT and 2QT.
_ 2 Energize the Aircraft Electrical Circuits from the External
_ Power (Ref. AMM TASK 24-41-00-861-002).
(b) If the FQIS is energized, reset the FQIC as follows: 1 Open the C/Bs 1QT and 2QT.
_
2 Wait 5 seconds.
_
3 Close the C/Bs 1QT and 2QT.
_ NOTE : For the FQIC to do a (new) power up BITE test, a power
____ supply interrupt (interval) of more than 5 seconds is necessary. This gives the current status of the FQIS components.
(2) Do the EIS Start Procedure (ECAM only) (Ref. AMM TASK 31-60-00-860-001).
(3) On the ECAM control panel, push (in) the FUEL P/BSW.
(4) Make sure that the FUEL page shows on the ECAM lower display unit.
(5) Wait 60 seconds.
(6) Continue as follows: NOTE : The FUEL page FQIs will show XXs in amber color, for 35
____ seconds, during the FQIC power up BITE test. A FQIS sensor fault must be sensed by the FQIC for 60 seconds before the applicable LRU identification is transmitted to the CFDS as unserviceable. The fault message is shown on the MCDU when set to SYSTEM REPORT/TEST (FUEL) and the FQIS STATUS page.
(a) Do the procedure to get access to the SYSTEM REPORT/TEST menu page (Ref. AMM TASK 31-32-00-860-001).
(b) When the SYSTEM REPORT/TEST menu page comes into view, push the line key adjacent to FUEL.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞28-42-00∞∞∞∞∞∞∞∞∞∞Page A279
201-299, 401-499, Aug 01/05 CES 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞28-42-00∞∞∞∞∞∞∞∞∞∞Page A280
(c) When the FUEL menu page 1 comes into view, push the NEXT PAGE key on the MCDU keyboard to see the FUEL menu page 2.
NOTE : If a menu has more than one page (shown by the more to____ come symbol > on the top line, right side of the MCDU display) each operation of the NEXT PAGE key on the MCDU keyboard will cause the next page to be shown. When the last page of any menu is shown, operation of the NEXT PAGE key will cause the first page to be shown.
(d) When the FUEL menu page 2 comes into view, push the line key adjacent to FQIS STATUS.
(7) Examine the FQIS STATUS page.
(8) If the message L(R) QTY PROBE 32QT1(2):
(a) Is not shown, maintenance steps are not necessary.
(b) Is shown, go to Para. 4.A.
R R NOTE : You can get data from the:____ - Description and Operation (D and O) section of the Aircraft Maintenance Manual (AMM), the Fuel Quantity Indicating System (FQIS) (Ref. AMM 28-42-00 P.Block 001) - Trouble-shooting Manual (TSM) - Task Supporting Data (Ref. P. Block 301) - Aircraft Schematic Manual (ASM) (Ref. ASM 28-42/07) ( (Ref. ASM 28-42/08)).
R R R NOTE : You can get more Trouble-shooting data from the____ CFDS(FUEL): - Input Parameters Page 2 (Ref. AMM TASK 28-42-00-740-003) - FQIC Trouble Shooting Data (Ref. AMM TASK 28-42-00-740-007).
NOTE : OPTIONAL TESTING:____ If a DC Capacitance Fuel System Tester is available, measurements can be taken before a decision is made to go into or close up a fuel tank. The Tester can be connected to the FQIC rack connector or the related tank wall connector. (Ref. P. Block 301 for the Tank Units DC Capacitance Values).
201-299, 401-499, Aug 01/05 CES
4. Fault Isolation
_______________
R **ON A/C 001-049, 051-061, 101-105, 201-203,
A. Procedure
NOTE : Where applicable, to show the difference between the left and
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 FUEL 燃油3(3)
