曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  B. Crimping with Fixed-Die Crimping Tools 
R  Using table below, select crimping tool according to wire and terminal to 
R  be crimped. Check tool condition, appearance and operation between two 
R  periodic checks. 
R  C. Insulation Crimping Adjustment Procedure 
R  (1) The insulation crimp section of each tool has three adjustment 
R  positions. 
R  (2) To perform adjustment, remove insulation adjustment pin from its 
R  housing and insert it in appropriate position. 
R  (3) Correct insulation grip is determined as follows : 
R  - Insert adjustment pin in No. 3 position. 
R  - Place terminal in crimping dies as for normal crimping. 
R  - Take wire appropriate to terminal and insert unstripped wire into 
R  only the insulation grip portion of the terminal. 
R  If two wires are crimped in the same terminal, perform grip test 
R  with two wires. 
R  - Crimp terminal 
R  - Remove terminal and check insulation grip as follows : bend wire 
R  back and forth, terminal sleeve should retain grip on wire 
R  insulation.

 

 Hand Crimping Tools-AMP P/N 576778, 576779, 576780, 484364-1, 576781, 576782, 576783, 576784, 69694-1 and 59461 R Figure 023

20-25-22 Page 4820-25-22 Page 4920-25-22 Page 50

R  - If wire pulls out, set insulation adjustment pin to No. 2 position 
R  and repeat test. 
R  - If test results are not satisfactory, set adjustment pin to No. 1 
R  position. 
R  (4) The following table gives the crimping adjustments currently in use. 
R  --------------------------------------------------------------
R  | | Cable Type | 
R  | Cable |-----------------------------------------| 
R  | Size | | NSA935130DE | 
R  | | E0261CF | E0260BE | 
R  | | | E0262DK | 
R  | |--------------------|--------------------| 
R  | | POSITION | 
R  |------------------|-----------------------------------------| 
R  | 24 | | 1 | 
R  |------------------| |--------------------| 
R  | 22 | | 2 | 
R  |------------------| 1 |--------------------| 
R  | 20 | | 1 | 
R  |------------------| |--------------------| 
R  | 18 to 10 | | 2 | 
R  |------------------------------------------------------------|

 

R  _______________________________________________________21. AMP Hand Crimping Tools P/N 69376-1, 69376-2 and 476408 
R  (Ref. Fig. 024) 
R  Example of connection P/N used with this tool 
R  --------------------------------------------------------------
R  |  CRIMPING TOOLS  |  CONNECTION  | 
R  |-------------------------|-----------------------------------| 
R  |  NORM  |  P/N  |  P/N  |  TYPE  | 
R  |------------|----------- |---------------|-------------------| 
R  |  AMP  |  69376-1  |  NSA938601  |  | 
R  |  AMP  |  69376-2  |  NSA938621  |  COAXIAL PLUGS  | 
R  |------------|------------|---------------|  | 
R  |  AMP  |  476408  |  NSA938601  |  | 
R  ---------------------------------------------------------------

 

 Hand Crimping Tools-AMP P/N 69376-1, 69376-2 and 476408 R Figure 024

20-25-22 Page 5120-25-22 Page 52

R  __________________________________________________22. PRONER Hand Crimping Tool BNC4 (P/N S111001129070) 
R  (Ref. Fig. 025) 
R  Example of connection P/N used with this tool 
R  ---------------------------------------------------------------
R  |  CRIMPING TOOLS  |  CONNECTION  | 
R  |--------------------------|-----------------------------------| 
R  |  NORM  |  P/N  |  P/N  |  TYPE  | 
R  |------------|-------------|---------------|-------------------| 
R  |  PRONER  |  "BNC4"  |  E0256  |  TERMINALS  | 
R  |  |S111001129070|  |  | 
R  ----------------------------------------------------------------
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 1(100)