Ignition System Test
Figure 501/TASK 74-00-00-991-300
F 『 EEFF : ALL E Page 50374-00-00
E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E
Ignition System Test Figure 502/TASK 74-00-00-991-301-A
F 『R EEFF : ALL E Page 50474-00-00
E E Aug 01/01 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
(Ref. Fig. 502/TASK 74-00-00-991-
301-A)
3. On the panel 115VU:
- Make sure that the ENG/MODE selector switch is in the NORM position.
4. Set the ENG/MASTER 1 (2) control switch to ON.
5. Push the line key adjacent to the PUSH BUTTON TO START TEST indication. (Ref. Fig. 502/TASK 74-00-00-991-
301-A)
6. Set the ENG/MASTER 1 (2) control switch to OFF.
7. Push the line key adjacent to the RETURN indication.
8. Do the procedure again for the channel B of the FADEC 1 (2).
(Ref. Fig. 502/TASK 74-00-00-991-301-A)
- The CAUTION: IGNITERS WILL CYCLEDURING TEST IGNITER A TESTED THEN Bindication comes into view
(Ref. Fig. 502/TASK 74-00-00-991-301-A)
- IGNITER A THEN B WILL CYCLE FOR 10 SECS EACH. Make sure that igniter 1 of the engine 1(2) makes noise for 10 seconds and after about 2 seconds the igniter 2 of the engine 1(2) makes noise for 10 seconds.
- TEST COMPLETE comes into view. When the test is finished (Ref. Fig. 502/TASK 74-00-00-991-301-A)
- The ENGINE menu comes into view.
F 『R EEFF : 001-049, 051-099, 101-149, 155-199, E Page 50574-00-00
E E201-299, 301-399, 401-499, Aug 01/05 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
9. On the MCDU, push the line key
adjacent to the RETURN indication
until the CFDS menu page comes
into view.
10. Stop the MCDU.
R **ON A/C 151-154,
Subtask 74-00-00-710-050-A
A. Do this test :
WARNING : MAKE SURE THERE IS NO AIR PRESSURE SUPPLIED AT THE STARTER
_______
VALVE INLET.
NOTE : This test is for the system 1. For the other system(s), use the
____
indications between the parentheses.
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the MCDU:
- Push the line key adjacent to the FADEC 1A (2A) indication.
2. Push the line key adjacent to the IGN TEST indication. (Ref. Fig. 502/TASK 74-00-00-991-
301-A)
3. On the ENG PNL 115VU:
- Make sure that the ENG/MODE selector switch is in the NORM position.
- The ENGINE 1(2) MAIN MENU page comesinto view. (Ref. Fig. 502/TASK 74-00-00-991-301-A)
- The IGNITION TEST menu comes intoview.
(Ref. Fig. 502/TASK 74-00-00-991-301-A)
F 『 EEFF : ALL E Page 50674-00-00
E E Aug 01/01 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
4. Set the ENG/MASTER 1 (2) control switch to ON.
5. Push the line key adjacent to the PUSH BUTTON TO START TEST
indication.
(Ref. Fig. 502/TASK 74-00-00-991-301-A)
6. Set the ENG/MASTER 1 (2) control switch to OFF.
7. Push the line key adjacent to the RETURN indication.
8. Do the procedure again for the channel B of the FADEC 1 (2).
9. On the MCDU, push the line key adjacent to the RETURN indication until the CFDS menu page comes into view.
10. Stop the MCDU.
- The WARNING TEST ACTIVE indicationcomes into view (Ref. Fig. 502/TASK 74-00-00-991-301-A)
- IGNITER 1 and 2 will cycle once for 10 seconds. Make sure that igniter 1 of the engine 1(2) makes noise for 10 seconds and after about 2 seconds the igniter 2 of the engine 1(2) makes noise for 10 seconds. 中國航空網(wǎng) m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM IGNITION 點火(5)
