(3)
Close the cockpit door (2) and make sure that it touches the safety angle (14).
(4)
Measure the clearance "J" between the latch tenon (22) and the catch
(23) of the center elctrical release strike (21).
NOTE : The clearance "J" must be between 0.5 mm (0.0196 in.) and 1.0
____
mm (0.0393 in.).
(5) If the clearance "J" is not in the limits, adjust the center electrical release strike (21) as follows (movement in rear direction):
(a)
Open the cockpit door.
(b)
Remove one of the long aluminum shims (24).
(c)
Add a short aluminum shim (25) with a thickness of 1 mm (0.0393 in.) between the spring pack (26) and the center electrical release strike (21).
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 52-51-00Page 549 1201-217, 1Aug 01/05 1 1 1CES 1
Cockpit Door - Adjustment
Figure 504A/TASK 52-51-00-991-003-B12 (SHEET 1)
R 1EFF : 106-149, 221-299, 301-399, 401-499, 1 52-51-00Page 550 1 1 Aug 01/05 1 1 1CES 1
Cockpit Door - Adjustment
Figure 504A/TASK 52-51-00-991-003-B22 (SHEET 2)
R 1EFF : 106-149, 221-299, 301-399, 401-499, 1 52-51-00Page 551 1 1 Aug 01/05 1 1 1CES 1
Cockpit Door - Adjustment
Figure 504B/TASK 52-51-00-991-003-A12 (SHEET 1)
R 1EFF : 218-220, 1 52-51-00Page 552 1 1 Aug 01/05 1 1 1CES 1
Cockpit Door - Adjustment
Figure 504B/TASK 52-51-00-991-003-A22 (SHEET 2)
R 1EFF : 218-220, 1 52-51-00Page 553 1 1 Aug 01/05 1 1 1CES 1
Electrical Release Strikes - Access
Figure 505/TASK 52-51-00-991-004- 12 (SHEET 1)
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 52-51-00Page 554 1201-217, 1Aug 01/05 1 1 1CES 1
Electrical Release Strikes - Access
Figure 505/TASK 52-51-00-991-004- 22 (SHEET 2)
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 52-51-00Page 555 1201-217, 1Aug 01/05 1 1 1CES 1
Electrical Release Strikes - Access Figure 505A/TASK 52-51-00-991-004-A
R 1EFF : 106-149, 218-299, 301-399, 401-499, 1 52-51-00Page 556 1 1 Aug 01/05 1 1 1CES 1
INTENTIONALLY BLANK
R 1 1
52-51-00Page 557
1 1 Aug 01/05 1 1 1CES 1
R Electrical Release Strikes - Adjustment Figure 506/TASK 52-51-00-991-005- 12 (SHEET 1)
1EFF : 001-049, 051-099, 101-105, 151-199, 1 52-51-00Page 558 1201-217, 1Aug 01/05 1 1 1CES 1
R Electrical Release Strikes - Adjustment Figure 506/TASK 52-51-00-991-005- 22 (SHEET 2)
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 52-51-00Page 559 1201-217, 1Aug 01/05 1 1 1CES 1
(d)
Make sure that the clearance "J" between the cockpit door (2) and the safety angle (14) is correct.
(e)
If not, remove the long aluminum shim (24) and add a second short aluminum shim (25) with a thickness of 1.0 mm (0.0393 in.).
(f)
Make sure that the clearance "J" is correct.
(6) Measure the clearance "H" between the latch tenon (22) and the catch
(23) of the upper and lower elctrical release strikes (21). NOTE : The clearance "H" must be between 1.0 mm (0.0393 in.) and 1.5
____
mm (0.0590 in.).
(7)
If the clearance "H" is not in the limits, adjust the upper and lower electrical release strikes (21) as follows (movement in rear direction):
(a)
Open the cockpit door.
(b)
Remove the long aluminum shim (24) with a thickness of 1.0 mm (0.0393 in.) and add a short aluminum shim (25) with a thickness of 1.0 mm (0.0393 in.).
(c)
Make sure that the clearance "H" is correct.
(d)
If not, remove the long aluminum shim (24) and add a second short aluminum shim (25) with a thickness of 1.0 mm (0.0393 in.).
(e)
Make sure that the clearance "H" is correct.
(8)
Install the access covers (17) as follows:
(a)
Remove the screws (18) and the safety angle (14) from lavatory wall (15).
(b)
Install the access covers (17) with the screws (18) on the housings (16).
(c)
Install the safety angle (14) with the screws (19) on the
lavatory wall (15).
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 52-51-00Page 560 1201-217, 1Aug 01/05 1 1 1CES 1R **ON A/C 106-149, 218-299, 301-399, 401-499,
Subtask 52-51-00-820-050-A
A. Adjustment of the Cockpit Door R **ON A/C 106-149, 221-299, 301-399, 401-499,
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊(cè) AMM DOORS 艙門7(47)
