(3)
Removal of the HOIST - MINILIFT from the APU compartment
(a)
Hold the HOIST - MINILIFT (10) in position and remove the quick release pin (8) from the bearing assy (7) on the LH side of the APU compoartment.
(b)
Hold the HOIST - MINILIFT (10) in position and remove the quick release pin (2) from the APU hoist bracket (1) on the top firewall of the APU compartment.
(c)
Remove the HOIST - MINILIFT (10) from the APU compartment.
(d)
Install the quick release pins (2) and (8) temporarily on the HOIST - MINILIFT (10).
Subtask 49-00-00-080-052
B. Removal of the HOIST - MINILIFT and SAFETY BELT - APU HOIST
(Ref. Fig. 203/TASK 49-00-00-991-010)
NOTE : Do the subsequent steps of this paragraph if the load compressor
____
scroll installed has the following P/N 2810315-3.
This are APU'S:
-with P/N 3800278-3 and CHANGE NO. 122 not incorporated.
-before P/N 3800278-3 SERIES NO. 12.
-upto P/N 3800278-3 SERIES NO. 11 CHANGE NO. 122 not incorporated.
(1)
Make sure that the APU is correctly installed and the APU mount nuts are correctly torqued (Ref. TASK 49-11-11-400-001).
(2)
Disconnection of the HOIST - MINILIFT (22) and the SAFETY BELT - APU HOIST from the APU
(a)
Turn the upper drum shaft of the HOIST - MINILIFT (22) in a counterclockwise direction until you have removed the tension from the cable (26).
(b)
Remove the quick release pin (31) and disconnect the shackle (36) from the APU.
(c)
Remove the bolts (29) and (34) from the shackles (28) and (35) and remove the saftey belt (30) from around the APU scroll (25)
(d)
Temorarily install the bolts (29) and (34) in the shackles (28) and (35).
(e)
Remove the qiuck release pin (33) and disconnect the shackle (36) from the cable (26) of the HOIST - MINILIFT (22).
(3)
Removal of the HOIST - MINILIFT from the APU compartment
(a)
Hold the HOIST - MINILIFT (22) in position and remove the quick release pin (23) from the bearing assy (24) on the LH side of the APU compoartment.
(b)
Hold the HOIST - MINILIFT (22) in position and remove the quick release pin (21) from the APU hoist bracket (20) on the top firewall of the APU compartment.
(c)
Remove the HOIST - MINILIFT (22) from the APU compartment.
(d) Install the quick release pins (21) and (23) temporarily on the HOIST - MINILIFT (22). ________
5. Close-up
Subtask 49-00-00-410-065
A. Close Access
(1)
Install the APU oil cooler outlet-duct (Ref. TASK 49-52-41-400-001)
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
(3)
Close or install the APU access door 315AL (Ref. TASK 52-41-00-410-001) or (Ref. TASK 52-41-21-400-001).
(4)
Set the light switch 11LJ to the off position.
(5)
Close the APU access door 316AR (Ref. TASK 52-41-00-410-001).
(6)
Remove the access platform(s). Subtask 49-00-00-865-087
B.
Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1KD, 2KD, 1WF, 2WF, 3WF, 4WF.
Subtask 49-00-00-860-058
C. Put the aircraft back to its initial configuration.
(1)
De-energize the ground service network (Ref. TASK 24-41-00-862-002).
(2)
Remove the warning notice(s).
(3)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
TASK 49-00-00-860-003 APU Start by External Power (GTCP 36-300) WARNING : DO NOT TOUCH THE APU UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS
_______ WHEN YOU DO THE MAINTENANCE TASK(S).
WARNING : WHILE THE APU OPERATES, DO NOT GO INTO THESE AREAS:
_______
-
THE AREA BEHIND THE APU EXHAUST DUCT: 25m (82ft.) REARWARD OF THE
DUCT, MORE THAN 3m (10ft.) ABOVE THE GROUND, AND THE WIDTH OF THE
HORIZONTAL STABILIZER
-
THE AREA AROUND THE APU AIR-INTAKE: 2m (7ft) AROUND THE INTAKE
-
THE AREA OF THE OIL-COOLER OUTLET.
THERE IS A RISK OF INJURY IF YOU GO INTO THESE AREAS.
CAUTION : DO NOT USE THE APU DURING FLUID DE-ICING OPERATIONS. DE-ICING FLUID
_______ CAN CONTAMINATE THE INSIDE OF THE APU.
CAUTION : DO NOT TRY TO START THE APU A FOURTH TIME UNTIL THE STARTER MOTOR IS
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER1(91)
