F 『
E C F M E
E E
E 56-5B E
E E
_______ (NEW O-RING AND THE RE-USED OR NEW SEAL RING). IF THE STARTER IS INSTALLED WITHOUT THESE SEALS, THE ENGINE CAN LEAK OIL. THIS CAN CAUSE ENGINE FAILURE.
(1) Remove the protective plugs.
R (2) Lubricate the new O-ring (50) with engine oil (Material No. CP2442) R and install in groove of starter output drive shaft.
PRE SB CFM56-5 72-094
(3) Lubricate the re-usable or new seal (40) with engine oil (Material No. CP2442) and install it in the starter drive pad of the accessory gearbox.
POST SB CFM56-5 72-094
(4) Install the seal ring assembly (40) as follows:
R (a) If necessary, install a new preformed packing (30) on the support (20).
(b) Lubricate the seal ring assembly (40) with engine oil (Material No. CP2442).
(c) Install the seal ring assembly (40) in the starter drive pad of the accessory gearbox. END OF SB CFM56-5 72-094
(5) Align locating dowel on starter (60) with locating hole on AGB housing . Engage the starter carefully in the drive pad to prevent damage to the O-ring (50). If necessary, turn the starter output drive shaft by hand to align mating splines.
(6) Put V-clamp (10) in position on the mating flanges. Lubricate the threads of clamp nut with graphite grease (Material No. CP2101). Install the nut and TORQUE to between 70 and 80 lbf.in (0.79 and 0.90 m.daN).
(7) Put the V-clamp (70) and the air supply duct (80) in position on the starter air inlet orifice. Lubricate the threads of clamp nut with graphite grease (Material No. CP2101). Install nut and TORQUE to between 70 and 80 lbf.in (0.79 and 0.90 m.daN).
(8) Fill starter with engine oil (Material No. CP2442) (Ref. TASK 12-13-80-610-001), if necessary.
F 『 EEFF : ALL E Page 40880-11-10
E E Aug 01/03 E E ECES E
F 『
E C F M E
E E
E 56-5B E E E Subtask 80-11-10-710-052
B. Test
CAUTION : DO NOT OPERATE THE ENGINE WITHOUT A CORRECTLY INSTALLED STARTER
_______ ON THE AGB STARTER DRIVE PAD. IF THE STARTER IS NOT INSTALLED CORRECTLY, THE ENGINE CAN HAVE OIL LEAKAGE. THIS CAN CAUSE ENGINE FAILURE.
(1) Do a minimum idle check and do a check for oil leaks at the starter drive pad an for air leaks at starter to air duct connection (Ref. TASK 71-00-00-710-006).
5. Close-up
________
Subtask 80-11-10-410-053
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Close the fan cowl doors: (Ref. TASK 71-13-00-410-040)
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
(3) Remove the warning notice(s).
F 『 EEFF : ALL E Page 40980-11-10
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
STARTER - INSPECTION/CHECK
__________________________
TASK 80-11-10-210-001
Check Chip Detector
1. Reason for the Job
__________________
Refer to the MPD TASK: 801110-C1
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific tissue paper
No specific warning notice
No specific 10-power magnifying glass
R No specific Torque Wrench : range 5.00 to 35.00 lbf.in
R (0.05 to 0.40 m.daN)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP2442 * engine oil (Ref. 70-30-00) Material No. CP8001 * lockwire 0.032 in. (0.8 mm) dia. (Ref. 70-30-00) Material No. CP8002 * lockwire 0.032 in. (0.8 mm) dia. (Ref. 70-30-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
40 O-ring 80-11-10 02 -130 70 O-ring 80-11-10 02 -130 100 O-ring 80-11-10 02 -090 100 O-ring 80-11-10 02 -100
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 起動 STARTING(11)
