(a) Identify the cable ends of the connector 4046VC1(4046VC2) (34).
(b) Use a crimping tool to crimp the connector pins on the wires of R the connector (34) (Ref. ESPM 203222).
(c)
Insert the connector pins into the connector (34) (Ref. WL 912840).
(d)
Tighten the clamp screws (36) of the backshell (35). Make sure that the cable is firmly clamped in the backshell (35).
(e)
Safety the clamp screws (36) and the backshell (35) with lockwire.
(f)
Install the new O-ring (30) on the connector (34).
(g)
Put the connector (34) in position in the hole in RIB15.
(h)
Get access through the opening 540KB(640KB) to RIB15.
R 1EFF : 106-149, 229-299, 401-499, 1 28-42-43Page 473 1 1 Aug 01/05 1 1 1CES 1
(i)
Install the washer (31) and the nut (32) on the connector (34).
(j)
TORQUE the nut to between 0.84 and 0.92 m.daN (74.33 and 81.41 lbf.in).
(k)
Safety the nut (32) with the anti-rotation plate (41), the bolts
(42)
and the nuts (40).
(l)
Apply SEALANTS (Material No. 09-001) around the connector (34) to seal it to the rear spar.
(m)
Remove the blanking cap and connect the plug connector (33) to the connector (34).
(n)
Clean the plug connector (33) with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
(o)
Apply a continuous layer of STORAGE PRESERVATION (Material No. 15-008) to the plug connector (33).
(p)
Get access through the opening 540JB(640JB).
(q)
Put the cable for the connector (34) in position.
(r)
Attach the harness 14QT1(14QT2) to the structure with the cable-ties (1).
(s)
Get access through the opening 540BB(640BB) to RIB7.
(t)
Identify the cable ends for the connector 4040VC1(4040VC2) (34).
(u) Use a crimping tool to crimp the connector pins on the wires of R the connector (34) (Ref. ESPM 203222).
(v)
Insert the connector pins into the connector (34) (Ref. WL 912840).
(w)
Tighten the clamp screws (36) of the backshell (35). Make sure that the cable is firmly clamped in the backshell (35).
(x)
Safety the clamp screws (36) and the backshell (35) with lockwire.
(y)
Remove the blanking cap and apply BONDING AND ADHESIVE COMPOUNDS (Material No. 08-013) to the threads of the connector (34).
(z)
Install the O-ring (30) on the connector (34).
R 1EFF : 106-149, 229-299, 401-499, 1 28-42-43Page 474 1 1 Aug 01/05 1 1 1CES 1
(aa) Put the connector (34) in position in the hole on the rear spar. (ab) Get access through the opening 574BB(674BB) to the rear spar. (ac) Install the washer (31) and the nut (32) on the connector (34). (ad) TORQUE the nut (32) to between 1.16 and 1.27 m.daN (102.65 and
112.38 lbf.in). (ae) Safety the nut (32) with MISCELLANEOUS (Material No. 19-010). (af) Apply SEALANTS (Material No. 09-001) around the connector (34) to
seal it to the rear spar. (ag) Remove the blanking cap and connect the plug connector (33) to
the connector (34). (ah) Get access through the opening 540BB(640BB). (ai) Remove the bolts (4) and the P clips (3) and put the cable (for
the connector (34)) in position. (aj) Attach the harness to the structure with the P clips (3), the bolts (4) and the cable-ties (1). R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 28-42-43-865-070
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1QJ, 1QP, 2QP, 3QP, 4QP, 1QT, 2QT, 8QT, 31QA, 32QA.
Subtask 28-42-43-740-057
D. Test
(1)
Do a status report (BITE) of the fuel-quantity indicating system (Ref. TASK 28-42-00-740-001).
(2)
Do a functional (BITE) test of the fuel-tank level-sensing system (Ref. TASK 28-46-00-740-001).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-42-43Page 475 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
5. Close-up
________ Subtask 28-42-43-410-063
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the applicable access panels (Ref. TASK 57-27-11-400-001), (Ref. TASK 57-27-11-400-002) and (Ref. TASK 28-12-46-400-001): FOR 14QT1
