R R  Distribution Line - Test (CFM56-5B) Figure 504/TASK 26-21-00-991-008- 22 (SHEET 2)
 1EFF : 1 1 1CES  ALL  1 111 26-21-00 Page 525 Feb 01/04

 -Disconnect the line (3) from the discharge head (2) and move the bottle (1) to get access to the line (3).
 -Remove the four screws and washers which attach the forward fire-extinguisher bottle (7).
 -Disconnect the line (4) from the discharge head (6) and move the bottle (7) to get access to the line (4).
 (b)
 Install the manifold adapter (14) TEST TOOL - ENGINE FIRE EXTINGUISHING SYSTEM, the clamp (13) and the flexible pipe (12) on the outlet B (detail F).

 (c)
 Connect the manifold assembly (11) TEST TOOL - ENGINE FIRE EXTINGUISHING SYSTEM to the flexible pipe (12).

R (d) Connect a compressed air source (up to 2.07 bars (30 psi)) to the R manifold assembly (11).
 (e)
 Open the compressed air source and make sure that the air flows from the outlets A, C, D, E, F and G (detail B) and H and J (detail C).

 (f)
 Close the compressed air source.

 (2) Leak test
 (a)
 Install the plug assy (8) TEST TOOL - ENGINE FIRE EXTINGUISHING SYSTEM on the outlets H and J of the lines (4) and (3) (details C and D).

 (b)
 Install the blanks (9) TEST TOOL - ENGINE FIRE EXTINGUISHING SYSTEM on the outlets E and F (detail H).

 (c)
 Install the blanks (10) TEST TOOL - ENGINE FIRE EXTINGUISHING SYSTEM on the outlets A, D, C and G (detail G).

 (d)
 Pressurize the line to 2.07 bars (30 psi).

R (e) Close the valve of the manifold assembly (11) to isolate the R extinguishing line.
 (f)
 During 5 minutes, make sure that there is no leakage: pressure must not decrease more than 0.13 bar (1.88 psi).

 (g)
 Close the compressed air source.

 (h)
 Open the drain valve to depressurize the extinguishing line.

 (i) Disconnect the compressed air source. R (j) Disconnect the manifold assembly (11) from the line.
 (k)
 Remove the blanks (10), the blanks (9) and the plug assy (8).

 (l)
 Remove the clamp (13), the flexible pipe (12) and the manifold adapter (14).

 5. Close-up
________
 Subtask 26-21-00-860-068

 A. Put the aircraft back to its initial configuration.
 (1)
 If the bottles were not installed, install them (Ref. TASK 26-21-41-400-001) and go to the step B.

 (2)
 Connect the lines (4) and (3) to the discharge heads (6) and (2) (Ref. TASK 26-21-41-400-001).

 (3)
 Install the four screws and washers which attach the aft fire-extinguisher bottle (1).

 (4)
 Install the four screws and washers which attach the forward fire-extinguisher bottle (7).

 Subtask 26-21-00-865-085
 B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1WE1, 1WE2, 2WE1, 2WE2
 Subtask 26-21-00-410-068
 C. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 On the left engine pylon, install the access doors: 415BL, 415BR.

 (3)
 On the right engine pylon, install the access doors: 425BL, 425BR.

R  (4) Close the left thrust reverser halves : 
R  (Ref. TASK 78-36-00-410-040) 
R  (a) For engine 1, 
R  452AR. 
R  (b) For engine 2, 
R  462AR. 
R  Subtask 26-21-00-440-055 
R  D. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041) 
R  Subtask 26-21-00-410-069 
R  E. Close Access 
R  (1) Close the fan cowl doors: 
R  (Ref. TASK 71-13-00-410-040) 
R  (a) For engine 1, 
R  437AL, 438AR. 
R  (b) For engine 2, 
R  447AL, 448AR. 
R  Subtask 26-21-00-942-063 
R  F. Put the aircraft back to its initial configuration. 
R  (1) Remove the warning notice(s). 
R  (2) Remove the access platform(s).

 TASK 26-21-00-710-004
 Operational Test of Fire Control Pushbutton Switch Sub-functions Related to Engine Shut Down and Isolation (With External Air-supply Unit)
 CAUTION : TO RESET THE ENG 1(2) APU FIRE PUSHBUTTON SWITCH:
_______
 -PUSH THE PUSHBUTTON SWITCH FULLY IN (LATCHED POSITION).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FIRE PROTECTION 防火2(12)