.
TO–FROM ambiguity indicator show a FROM indication.
Copyright . The Boeing Company. See title page for details.
11.10.20 December 1, 2000
Flight Management, Navigation -Controls and Indicators 737 Operations Manual
ILS TEST Switches With an ILS frequency selected: Push UP/LT–
.
the glideslope indicates one dot up
.
localizer indicates one dot left. Push DN/RT–
.
the glideslope indicates one dot down
.
localizer indicates one dot right.
Frequency Indicator
Indicates the frequency selected by the frequency selector.
Frequency Selector
Rotate – manually selects the desired frequency.
VHF NAV Transfer Switch
VHF NAV Transfer Switch
BOTH ON 1 – switches the VHF navigation source to VHF NAV receiver No. 1.
NORMAL – VHF navigation source is from default VHF NAV receiver.
BOTH ON 2 – switches the VHF navigation source to VHF NAV receiver No. 2.
Flight Management, Navigation -Controls and Indicators
Transponder Panel
Transponder Air Traffic Control (ATC) Switch
1 – selects transponder No. 1. STBY – does not transmit. 2 – selects transponder No. 2.
ATC Code Indicator
Shows transponder code.
Identification (IDENT) Switch
Push – transmits an identification signal.
ATC Code Selectors
Rotate – sets transponder code in transponder.
Reply Light
Illuminated (green) –
.
transponder replying to ground interrogation
.
test in progress.
Altitude Reporting (ALT RPTG) Switch
1 – enables altitude reporting from air data computer No. 1. OFF – transponder operates without altitude reporting.
Copyright . The Boeing Company. See title page for details.
11.10.22 June 8, 2001
Flight Management, Navigation -Controls and Indicators 737 Operations Manual
2 – enables altitude reporting from air data computer No. 2.
Test Switch
Push – with the transponder air traffic control (ATC) switch in position 1 or 2, the reply light illuminates to indicate the selected transponder is operational.
Altitude Reporting (ALT RPTG) Switch
ON – enables altitude reporting.
OFF – transponder operates without altitude reporting.
ATC Code Indicator
Shows transponder code.
ATC Code Selectors
Rotate – sets transponder code in transponder.
Identification (IDENT) Switch
Push – transmits an identification signal.
Transponder Mode Selector
L – selects transponder No. 1.
STBY – does not transmit.
R – selects transponder No. 2.
Flight Management, Navigation -Controls and Indicators 737 Operations Manual
Altitude Reporting (ALT RPTG) Switch
1 – enables altitude reporting from air data computer No. 1. OFF – transponder operates without altitude reporting. 2 – enables altitude reporting from air data computer No. 2.
ATC Code Indicator
Shows transponder code.
ATC Code Selectors
Rotate – sets transponder code in transponder.
FAULT Light
Illuminated (amber) – indicates transponder malfunction.
Identification (IDENT) Switch
Push – transmits an identification signal.
Transponder Mode Selector
TEST – starts ATC transponder functional test for transponder No. 1.
1 – selects transponder No. 1.
STBY – does not transmit.
2 – selects transponder No. 2.
TEST – starts ATC transponder functional test for transponder No. 2.
Copyright . The Boeing Company. See title page for details.
11.10.24 December 1, 2000
As installed
AFT ELECTRONIC PANEL
Transponder (XPNDR) Selector
1 – selects transponder No. 1. 2 – selects transponder No. 2.
ATC Code Indicator
Shows transponder code.
Shows operating transponder (1 or 2).
Altitude Source Selector
1 – enables altitude reporting from ADC No. 1. 2 – enables altitude reporting from ADC No. 2.
Air Traffic Control (ATC) Code Selector
Rotate – sets transponder code in transponder.
Transponder (XPNDR) FAIL Light
Illuminated – indicates transponder malfunction.
Transponder Mode Selector
STBY – disables transponder modes.
Note: Transponder modes are enabled only when the airplane is airborne, except for mode S, which operates continuously when the transponder mode selector is out of STBY.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300機組操作手冊Flight Crew Operations Manual FCOM 3(28)
