In-Service Wear Limits - Inspection Points Figure 602/TASK 21-61-52-991-009- 12 (SHEET 1)
R 1EFF : 001-003, 051-054, 1 21-61-52Page 608 1 1 May 01/05 1 1 1CES 1

 In-Service Wear Limits - Inspection Points Figure 602/TASK 21-61-52-991-009- 22 (SHEET 2)
R 1EFF : 001-003, 051-054, 1 21-61-52Page 609 1 1 May 01/05 1 1 1CES 1 Subtask 21-61-52-220-053

 C. In-Service Wear Limits
 (1) Use applicable measurement equipment and measure the OD of the bolt
 (7) and the ID of the bushing (11).
 NOTE : If any of the components are 'out of limits' then you must
____
 replace them.

 -for item (11) you must replace the bracket assembly (10) (Ref. TASK 21-61-52-000-001).
 -------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | AA | 6.325 | 6.335 | | | 6.318 | | | | OD 7 |(0.2490) |(0.2494) | | |(0.2487) | | | | | | | 0.015 | 0.061 | | | 0.075 | | | | | (0.0005)| (0.0024)| | |(0.0029)| | AA | 6.350 | 6.386 | | | | 6.393 | | | ID 11 |(0.2500) |(0.2514) | | | |(0.2516) | | -------------------------------------------------------------------------------
Subtask 21-61-52-220-054
 D. In-Service Wear Limits
 (1) Use applicable measurement equipment and measure the OD of the bolt
 (8) and the ID of the bushing (15).
 NOTE : If any of the components are 'out of limits' then you must
____
 replace them.

R 1EFF : 001-003, 051-054, 1 21-61-52Page 610 1 1 May 01/05 1 1 1CES 1

 -------------------------------------------------------------------------------
| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | BB | 6.325 | 6.337 | | | 6.318 | | | | OD 8 |(0.2490) |(0.2494) | | |(0.2487) | | | | | | | 0.013 | 0.040 | | | 0.054 | | | | | (0.0005)| (0.0015)| | |(0.0021)| | BB | 6.350 | 6.365 | | | | 6.372 | | | ID 15 |(0.2500) |(0.2505) | | | |(0.2508) | | -------------------------------------------------------------------------------
Subtask 21-61-52-220-055
 E. In-Service Wear Limits
 (1) Use applicable measurement equipment and measure the OD of the bolt
 (8) and the ID of the shouldered bushing (4).
 NOTE : If any of the components are 'out of limits' then you must
____
 replace them.

 -for item (4) (Ref. TASK 21-61-00-300-001).
 -------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | BB | 6.325 | 6.337 | | | 6.318 | | | | OD 8 |(0.2490) |(0.2494) | | |(0.2487) | | | | | | | 0.013 | 0.040 | | | 0.054 | | | | | (0.0005)| (0.0015)| | |(0.0021)| | BB | 6.350 | 6.365 | | | | 6.372 | | | ID 4 |(0.2500) |(0.2505) | | | |(0.2508) | | -------------------------------------------------------------------------------
R 1EFF : 001-003, 051-054, 1 21-61-52Page 611 1 1 May 01/05 1 1 1CES 1 Subtask 21-61-52-220-056

 F. In-Service Wear Limits
 (1) Use applicable measurement equipment and measure the OD of the bushing (15) and the ID of the shouldered bushing (3).
 NOTE : If any of the components are 'out of limits' then you must
____
 replace them.

 -for item (3) (Ref. TASK 21-61-00-300-001).
 -------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | BB | 9.983 | 9.994 | | | 9.976 | | | | OD 15 |(0.3930) |(0.3934) | | |(0.3927) | | | | | | | 0.006 | 0.035 | | | 0.049 | | | | | (0.0002)| (0.0013)| | |(0.0019)| | BB | 10.000 | 10.018 | | | | 10.025 | | | ID 3 |(0.3937) |(0.3944) | | | |(0.3946) | | -------------------------------------------------------------------------------
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM AIR CONDITIONING 空調 5(90)