Pack Inlet-Pressure Sensor Figure 401/TASK 21-61-16-991-001- 12 (SHEET 1)
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 21-61-16Page 404 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1

 Pack Inlet-Pressure Sensor Figure 401/TASK 21-61-16-991-001- 22 (SHEET 2)
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 21-61-16Page 405 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1 TASK 21-61-16-400-002

 Installation of the Pack-Inlet Pressure Sensor 16HH (36HH)
 WARNING : MAKE SURE THAT AIR IS NOT SUPPLIED TO THE AIR CONDITIONING SYSTEM
_______
 FROM THE MAIN ENGINE, THE APU OR A GROUND SOURCE.
 HOT COMPRESSED AIR CAN CAUSE INJURY TO PERSONNEL.

 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft)

 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
12-33-21-618-001 Pre-conditioning through the HP Ground Connection 12-33-21-618-001 Pre-conditioning with the APU 20-28-00-912-002 Electrical Bonding of Components With Conductive
 Bolts and Screws in the Tanks 21-61-00-710-001 Operational Test of the Pack Temperature-Control System 24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied from the External Power 53-35-13-000-002 Removal of the Quick-Release Access Panels from the Belly Fairing Structure 53-35-13-400-002 Installation of the Quick-Release Access Panels on the Belly Fairing Structure 21-61-16-991-001 Fig. 401
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 21-61-16Page 406 1201-299, 301-302, 1May 01/05 1 1 1CES 1

 3. Job Set-up
__________
 Subtask 21-61-16-860-050
 A. Aircraft Maintenance Configuration
 (1) Make sure that:
 (a)
 The aircraft electrical circuits are energized (Ref. TASK 24-41-00-861-002).

 (b)
 The access panel is removed (Ref. TASK 53-35-13-000-002),

R 1_FOR 16HH 191KB.
R 2_FOR 36HH 192KB.
 Subtask 21-61-16-865-053
 B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 16HH
 122VU AIR COND/PACK TEMP/CTL SYS1/1/115VAC 1HH X22 122VU AIR COND/PACK TEMP/CTL SYS1/1/28VDC 3HH X21 122VU AIR COND/PACK TEMP CTL SYS2/1/28VDC 4HH Y19 122VU AIR COND/PACK TEMP CTL SYS2/1/115VAC 2HH Y18
 FOR 36HH 122VU AIR COND/PACK TEMP/CTL SYS1/2/115VAC 21HH W22 122VU AIR COND/PACK TEMP/CTL SYS1/2/28VDC 23HH W21 122VU AIR COND/PACK TEMP CTL SYS2/2/28VDC 24HH Y21 122VU AIR COND/PACK TEMP CTL SYS2/2/115VAC 22HH Y20
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 21-61-16Page 407 1201-299, 301-302, 1May 01/05 1 1 1CES 1

 4. Procedure
_________
 (Ref. Fig. 401/TASK 21-61-16-991-001)
 Subtask 21-61-16-420-051
 A. Installation of the Pack-Inlet Temperature Sensor
 (1)
 Clean the component interface and/or the adjacent area.

 (2)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

R  (a) FOR 16HH 1 Put the clamps (2) in position on the pack-inlet pressure
_
 sensor (10).

 2 Put the pack-inlet pressure sensor (10) in position on the
_
 bracket (11).

 3 Install the bolts (4) and the washers (3).
_ 4 Put the bonding strap (7) in position and install the screw
_ (6), the washer (8) and the nut (9) (Ref. TASK 20-28-00-912-002).
 5 Remove the blanking caps from the disconnected electrical
_
 connectors.

 6 Make sure that the electrical connectors are clean and in the
_
 correct condition.

 7 Connect the electrical connector (5).
_ 8 Remove the blanking plugs from the disconnected line ends and
_ connect the pressure sense line (1).
 9 TORQUE the pressure sense line-connector (1) to between 0.95
_ and 1.05 m.daN (84.07 and 92.92 lbf.in).
 10 Make sure that the work area is clean and clear of tool(s) and
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM AIR CONDITIONING 空調 5(29)