B. De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
1EFF : ALL 1 21-26-51Page 503 1 1 May 01/04R 1 1 1CES 1
VALVE - SKIN AIR INLET (15HQ) - REMOVAL/INSTALLATION
____________________________________________________ TASK 21-26-52-000-001 Removal of the Avionics Ventilation Skin Air Inlet Valve (15HQ)
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific access platform 1.6 m (5 ft. 3 in.)
No specific access platform 1 m (3 ft. 3 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 21-26-52-991-001 Fig. 401
3. Job Set-up
__________ Subtask 21-26-52-861-052
A. Energize the ground service network
(Ref. TASK 24-42-00-861-001).
Subtask 21-26-52-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AIR COND/AVNCS VENT/CTL 6HQ D06 49VU AIR COND/AVNCS VENT/CTL 5HQ D05 122VU AIR COND/AVNCS/VENT/MONG 3HQ Y17
Subtask 21-26-52-010-050
C. Get Access
(1)
Put the access platform in position at the access door 824.
(2)
Open the access door 824.
(3)
Put the access platform in position on the left side of the aircraft, below the valve.
4. Procedure
_________ (Ref. Fig. 401/TASK 21-26-52-991-001) Subtask 21-26-52-020-050
A. Remove the Skin Air Inlet Valve
(1)
Remove the screws (3) and release the valve (4).
(2)
Disconnect the electrical connector (5).
(3)
Remove the valve (4) and discard the O-ring (2).
(4)
Remove the sealant from the valve (4) and structure (1).
(5)
Clean the areas where sealant was applied with CLEANING AGENTS (Material No. 11-004).
(6)
Put blanking caps on the disconnected electrical connectors.
(7)
Put a blanking plug on the air inlet.
Skin Air Inlet Valve
Figure 401/TASK 21-26-52-991-001
1EFF : ALL 1 21-26-52 Page 403
1 1 Feb 01/98
1 1
1CES 1
TASK 21-26-52-400-001
Installation of the Avionics Ventilation Skin Air Inlet Valve (15HQ)
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 1.6 m (5 ft. 3 in.) No specific access platform 1 m (3 ft. 3 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 09-019 USA AMS 3267/3 LOW ADHESION CORROSION INHIBITING SEALANT (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
O-ring 21-26-01 11A-020
1EFF : ALL 1 21-26-52Page 405 1 1 Aug 01/02R 1 1 1CES 1
D. Referenced Information
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM AIR CONDITIONING 空調 2(85)
