(g)
 Operate the empty oil gun 15 times to put air into the flap actuator and push out unwanted semi-fluid. Make sure that you operate the oil gun handle through its full range each time.

 (h)
 Disconnect the oil gun from the vent plug adaptor.

 (i)
 Remove the vent plug adaptor from the flap actuator.

 (j)
 Disconnect the waste hose from the drain plug adaptor.

 (k)
 Remove the drain plug adapter from the flap actuator.

 (l)
 Install (but do not torque tighten) the vent plug (1) in the flap actuator.

 (m)
 Install (but do not torque tighten) the drain plug (2) in the flap actuator.

 (3)
 Do the steps (2)(a) thru (2)(m) and remove unwanted semi-fluid from the:

 -
flap actuator No.2 6211CM(6261CM)

 -
flap actuator No.3 6221CM(6271CM)

 -
flap actuator No.4 6233CM(6283CM).

 (4)
 Operate the flaps through their full range of travel five times again (Ref. TASK 27-50-00-866-011) and (Ref. TASK 27-50-00-866-012). After the last operation, make sure that the flaps are in the fully extended position.

 (5)
 Do the steps (2)(a) thru (2)(m) again for the:

 -
flap actuator No.1 6205CM(6255CM)

 -
flap actuator No.2 6211CM(6261CM)

 -
flap actuator No.3 6221CM(6271CM)

 -
flap actuator No.4 6233CM(6283CM).

R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 12-13-27Page 351 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1

 (6)
 Torque tighten the vent plug (1) of each flap actuator as follows:

 (a)
 Remove the vent plug (1) from the flap actuator.

 (b)
 Apply SPECIAL MATERIALS (Material No. 05-115) to the mating surfaces of the vent plug (1) and the offset gearbox.

 (c)
 Install the vent plug (1) in the offset gearbox. TORQUE the vent plug (1) to between 0.54 and 0.66 m.daN (47.78 and 58.40 lbf.in).

 (7)
 Torque tighten the drain plug (2) of each flap actuator as follows:

 (a)
 Remove the drain plug (2) from the flap actuator.

 (b)
 Apply SPECIAL MATERIALS (Material No. 05-115) to the mating surfaces of the drain plug (2) and the offset gearbox.

 (c)
 Install the drain plug (2) in the offset gearbox. TORQUE the drain plug (2):

 -
flap actuator No.1 to between 0.54 and 0.66 m.daN (47.78 and

 58.40 lbf.in)

 -
flap actuator No.2 to between 0.54 and 0.66 m.daN (47.78 and

 58.40 lbf.in)

 -
flap actuator No.3 to between 0.36 and 0.44 m.daN (31.85 and

 38.93 lbf.in)

 -
flap actuator No.4 to between 0.36 and 0.44 m.daN (31.85 and

 38.93 lbf.in)
 5. Close-up
________
 Subtask 12-13-27-410-056

 A. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
R (2) FOR 6205CM, 6255CM
 (a)
 Remove the GROUND LOCK SLEEVE from the MLG.

 (b)
 Close the applicable MLG door 734, 744 (Ref. TASK 32-12-00-410-001).

R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 12-13-27Page 352 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1

 (3) Close the applicable access door:

 FOR 6211CM
 -
close the access door 573AB
 FOR 6261CM

 -
close the access door 673AB
 FOR 6221CM

 -
close the access door 575BB
 FOR 6271CM

 -
close the access door 675BB
 FOR 6233CM

 -
close the access door 575FB
 FOR 6283CM

 -
close the access door 675FB

 (4) Remove the access platform(s). Subtask 12-13-27-865-060
 B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
 Subtask 12-13-27-860-055
 C. Put the Aircraft Back to its Original Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
 (1)
 Retract the spoilers 1 thru 5 (Ref. TASK 27-60-00-866-002).

 (2)
 Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slat control lever (Ref. TASK 27-00-00-080-002).

 (3)
 Retract the flaps fully (Ref. TASK 27-50-00-866-009).

 Subtask 12-13-27-942-058
 D. Removal of Equipment
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM SERVICING 1(79)