曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

4. Limitations:
There are no limitations established for the horizontal stabilizer system at the time
of this revision.
OPERATING MANUAL
2A-27-00 PRODUCTION AIRCRAFT SYSTEMS
Page 50
October 11/02
Revision 8
Horizontal Stabilizer
System Simplified Block
Diagram
Figure 16
OPERATING MANUAL
2A-27-00
Page 51 / 52
October 11/02
Flaps / Horizontal
Stabilizer System Controls
and Indications
Figure 17
OPERATING MANUAL
2A-27-00
Page 53 / 54
October 11/02
2A-27-60: Flaps System
1. General Description:
The flaps system for the Gulfstream IV provides a means for the flight crew to
control the position and movement of the trailing edge flaps, in order to allow
steeper approach and climb angles, and lower takeoff and landing speeds.
The flaps are manually operated, electrically controlled, hydraulically powered,
mechanically actuated airfoils located on the inboard trailing edge of the left and
right wings. Designed as single-slotted Fowler-type flaps, they ride on rollers
along four curved flap tracks attached to the rear beam of each wing.
Mechanical actuators (commonly referred to as screwjacks), driven by a hydraulic
motor through a central gearbox, extend and retract the flaps. As the screwjacks
extend the flaps, the flaps move aft and downward to increase wing area and
camber.
An asymmetry protection system monitors flap position to prevent unequal
movement. If one flap moves further than the other, the protection system stops
flap movement by shutting off the hydraulic pressure source to the hydraulic
motor.
A FLAP handle, located on the center pedestal, controls normal flap extension
and retraction to four positions. Emergency flap control is provided by an EMER
FLAP handle located on the copilot’s right console. Flap position is displayed on
the FLAP / STAB position indicator located on the copilot’s skirt panel.
Extending the flaps normally results in a nose pitch down movement as the flaps
increase wing lift. To compensate for nose pitch down, the horizontal stabilizer
leading edge moves down corresponding to flap extension. Horizontal stabilizer
operation is described in Section 2A-27-50, Horizontal Stabilizer System.
Units and components in the flaps system receive electrical power from the
Essential DC bus. The primary source of hydraulic power for the system is the
Combined hydraulic system, with the Utility hydraulic system available as a
backup source. If both the Combined and Utility hydraulic systems are not
available, the Auxiliary hydraulic system can be used to position the flaps using
the AUX pump.
The flap system is composed of the following subsystems, units and components:
• Flap handles
• Flap shutoff valve
• Flap selector valve
• Hydraulic motor and central gearbox
• Flap actuators
• Flap follow-up switches
• Flap asymmetry protection system
• Flap position indication system
• Aircraft configuration warning system
• Flap control circuit breakers
A description of flap operation is also provided in this section.
2. Description of Subsystems, Units and Components:
(See Figure 17 through Figure 20.)
OPERATING MANUAL
PRODUCTION AIRCRAFT SYSTEMS 2A-27-00
Page 55
October 11/02
Revision 8
A. Flap Handles:
Normal positioning of the flaps is accomplished by a FLAP handle located
on the right side of the cockpit center pedestal. It has four detents that set
the flaps to each of its positions: UP (0°), 10°, Takeoff / Approach (T/O /
APPR [20°]) and DOWN (39°). The handle moves vertically into each
detent. At each detent, operating limit switches control electrical power to
the flap circuitry.
An EMER FLAP handle on the copilot’s side console mechanically controls
the flap selector valve if the normal flap control system malfunctions. The
handle moves vertically to select one of three detents: FLAPS UP,
NEUTRAL (no movement) or FLAPS DOWN. Before using the EMER
FLAP handle, however, the EMERG FLAP switch (just aft of the EMER
FLAP handle) must be in the EMERG position in order to bypass the
normal FLAP handle switches and flap follow-up switches.
If both the Combined and Utility hydraulic systems are not available, the
Auxiliary hydraulic system can be used to position the flaps using the AUX
pump. In this scenario, the normal FLAP handle would still be used.
During normal FLAP handle operation, both the FLAP CONT and MANUAL
FLAP CONT circuit breakers must be set. During EMER FLAP handle
operation, only the MANUAL FLAP CONT circuit breaker must be set.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：灣流4操作手冊 Gulfstream IV Operating Manual 2(21)